Magsafe Charging Pad for 2015-2021 Porsche Macan
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A low profile frame for a Anker PixelSnap/Magsafe Qi2 charger in the center console of a pre-2022 Porsche Macan
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 64
- Wydruki
- 0
- Wyświetlenia
- 397
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial
This is a frame to hold an Anker PixelSnap/Magsafe Qi2 wireless charger in the center console of any pre-2022 facelift Porsche Macan without the smoker package. If you have a lid on your center console, you have the smoker package, and this won't fit.
There are other models out there which are probably better for most use cases, but I wanted to hide all of the electronics, and I needed my phone to sit a little further forward, away from the cup holders.
The model puts ~1mm of plastic between the charger and phone, which wasn't enough to significantly affect charging speed in my testing. The magnets could be stronger, but my phone hasn't slipped yet. If you need to reduce the thickness, you can sink the cover into your build plate in your slicer.
I was only able to test this with a Pixel 10, but as far as I can tell, this is compatible with iPhones with magsafe.
Parts List
4x M3x8mm bolts
1x Anker Zolo Qi2 USBC Charger
1x USBC 12v Car Charger, as low profile as you can find. I used this one but it doesn't matter much.
1x Sheet of stick-on felt/flocking from a craft store. You only need a 2x27cm strip of it.
1x 3x5mm magnet (3mm tall, 5mm diameter)
1x Cover printed in ABS, sanded and acetone-smoothed
1x Frame printed in ABS
Printing/Assembly Instructions
Use ABS for the entire project.
Print the cover first. Orient it face-down on your printer to avoid any bridging artifacts. Direct your slicer to put the seams along the top edge, which will face the front of the car so you won't see them as often.
Sand the cover smooth with 180grit sandpaper. I should have done another round of this in my build, you can still see some of the texture in my pictures.
Use acetone to smooth the cover even further. You could also vinyl-wrap the cover and use the frame to secure things, but I haven't personally tried this.
Check the correct orientation for your 3x5mm magnet by holding it against your phone, then glue it into the 5mm hole at the bottom of the cover.
Press your wireless charger into the circle on the bottom of the cover. This should barely be a friction fit, you may need to sand around the edges a little bit.
Print the frame. I recommend flipping this upside down as well to reduce the amount of support material needed.
Sand any sharp/high spots from the top edge which will press the charger into the cover.
With the charger pressed into the cover, thread the cable through the lower opening on the frame and align the bolt holes.
Use your M3 bolts to attach the cover to the frame, sandwiching the charger into place. Don't over-torque the bolts.
Coil the charging cable and tuck the coil into the frame, leaving ~6in of cable free to work with later.
Cut your felt strip and wrap it around the outside of the bottom. This should give a nice friction fit with the center console of the car, without any risk of damaging it.
Plug your charger into the 12v car adapter, and plug the car adapter into the 12v port in the center console.
Manage the cable and press the whole assembly into the coin tray to seal the electronics in. There should not be much resistance, the felt should hold things in place.