1 / 3
Reifenmarkierset für Ventil und Radschraubenloch / Tire markers for valve and screw hole — zdjęcie 1
1 / 3

Reifenmarkierset für Ventil und Radschraubenloch / Tire markers for valve and screw hole

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Reifenkennzeichnungen / Tire marking set

Ocena
5 / 5
Polubienia
3
Pobrania
11
Wydruki
1
Wyświetlenia
76
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

----for english, please scroll down----

simples Reifenmarkierset mit deutschen Abkürzungen (VR/VL/HR/HL) zum Kennzeichnen der Reifen, da mir die, die ich finden konnte, alle nicht so recht gefallen haben. Diese hier sind so geformt, daß man sie wahlweise auf den Gummihals des Ventils stecken oder sie mit der leicht konischen Außenseite in die Löcher für die Radschrauben klemmen kann.

ACHTUNG: Damit die Markierungen auf dem Gummischaft des Ventils halten, müssen die Ventilkappen ein wenig dicker sein als der Gummischaft des Ventils. Bei Plastikkappen ist das meines Wissens immer der Fall. Die alten Metallkappen für Autoventile (siehe Photo bei "Makes") sind aber kleiner als der Gummischaft, da funktioniert das nicht. Hier muß die Version mit 8,1mm-Bohrung genommen werden, die dann auf dem Ventilgewinde sitzt.

Die farbige Markierung einfach über das "Multimaterial-Bemalung"-Tool von Prusaslicer machen; die Textflächen sind auf beiden seiten vorhanden und im Modell passend getrennt.

Gedruckt aus PLA, Supports sind nicht notwendig.

Update - verschiedene Bohrungsdurchmesser ergänzt:

  • Ordner "⌀8.1 mm für Metallkappen - for metal caps": Version mit 8,1mm-Bohrungsdurchmesser zum Aufsetzen auf das Ventilgewinde, für Metallventilkappen

  • Ordner "⌀8.1 mm Langloch für Metallkappen - slot for metal caps": Version mit 8,1mm-Bohrungsdurchmesser als Langloch zum Aufsetzen auf das Ventilgewinde, für Metallventilkappen. Kann freier herumbaumeln und etwas kippen, falls das gewünscht ist.

  • Ordner ⌀9.8 mm/⌀9.9 mm/⌀10.0 mm für Kunststoffkappen - for plastic caps: die ursprüngliche Version zum Aufschieben auf den Gummihals des Ventils, mit Bohrungsdurchmesser 9,8mm, 9,9mm und 10,0mm. Hier am besten ausprobieren, welche Version man am besten auf den Gummihals des Ventils klemmen kann, die aber noch von der Ventilkappe festgehalten wird.  Nach Bedarf die Öffnung etwas nachbohren, die Gummihälse der Ventile sind immer wieder mal etwas unterschiedlich dick - die Öffnung sollte aber kleiner bleiben als der Außendurchmesser der Ventilkappe!

---

A simple tire marking set with German abbreviations (VR/VL/HR/HL) for labeling tires, since I didn’t really like the ones I could find. These here are designed so that you can either push them over the rubber neck of the valve or push them into the wheel bolt holes with the slightly conical outside.

CAUTION: If you plan to use the markers on the rubber shaft of the valve as I do, the valve caps need to be a little larger than the rubber shaft of the valve. AFAIR this is always the case for plastic caps, but not for the old metal caps (see photo in the "Makes" section). Use the variant with 8.1mm hole in this case, which is placed on the valve thread instead.

Simply apply the colored markings using Prusaslicer’s “multi-material painting” tool; the text areas are present as separate surfaces on both sides.

Printed with PLA, no supports necessary.

Update - added different drill diameters:

  • Folder "⌀8.1 mm für Metallkappen - for metal caps":  8.1mm drill diameter, to be placed on valve thread, for metal valve caps

  • Folder "⌀8.1 mm Langloch für Metallkappen - slot for metal caps": variant with an 8.1mm slot hole, to be placed on valve thread, for metal valve caps. Can dangle more freely and tilt a bit, if that is wanted.

  • Folder ⌀9.8 mm/⌀9.9 mm/⌀10.0 mm für Kunststoffkappen - for plastic caps: the original variant to be pushed onto the rubber shaft of the valve, with drill diameters 9.8, 9.9 and 1.0 mm. Choose the one which fits snugly over the rubber shaft of the valve but does still has a smaller hole than the diameter of the valve cap. Drill the hole slightly wider if necessary, the diameter of the rubber necks of the valves varies - take care not to drill wider than the cap is though!

Tagi