PVS Yorkshire-14 MX10160 gen2+ analog nightvision
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Maybe your entry in into anlog night vision like it was for me, inside a compact and awesome looking design.
- Ocena
- 0 / 5
- Polubienia
- 29
- Pobrania
- 172
- Wydruki
- 0
- Wyświetlenia
- 1410
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a 3D-printable hobbyist model. It is not designed to meet military specifications or for use with restricted image intensifier tubes. Users are responsible for complying with their local export and firearm laws."
The pictured final device was printed in Polymaker ASA Fiberon CF08
The 100OHM resistor is used for the IR Illuminator and goes directly in series to it to reduce the powerdraw from the 3volt CR123A battery to around 17-20mA.
The cost of this build using the parts I used, also depending if you have some of the easy to get stuff already at home runs from 1030 to I guess 1100€ max. (rough estimate, your milage may vary) Cost could of course skyrocket depending on the tube you are going to use in here.
Follow the pictures in chronological order and pretty much everything should be self explanatory, if there are still questions feel free to ask them on the discord.
Join the PVS420 Discord where you can find the ongoing development of the Yorkshire-14 https://discord.gg/Ce9BJ2DK3j
UPDATE 26.05.2026
Added 850 band pass filter link to parts list and also added the band pass filer Frame 3d file.
______________________________________________________________________________________________________________
Important building tipps!:
One of the most important things you have to check is the polarity of your tube and the contact pins!
IF you reverse the Polarity cou could KILL YOUR TUBE!!!! Something you absolutely dont want for the most expensive toilett rolls out there!
Solder a tiny spot on the brass tube before you insert it into the battery assembly, (check pictures) you need proper heat as the metal of the brass tube will give you a hard time getting the solder to stick! Once the tube is inserted in the battery assembly ( use glue and cover the whole outer wall of the tube evenly) solder a cable to the spot we already prepared, again this will use high heat, got up to 400- 450° if you can and let your solder iron heat up properly, it will take a while for he cable to stick because of the thermal transfer capability of the brass tube, make sure the solderpoint is legit and properly melted!
Use super glue for the tiny micro switch cut off the two leads on the back as they are not needed and bend the front ones up so it is easier to solder once it is glued glued on the cover plate. I used some uv glued once it all was soldered to secure the cables in place. Dont forget the protectiv plastic stripe over the micro switch, I usted a stripe of that typical blister packaging, its sturdy almost undestructable thick plastic. ( check pictures)
One cable from the main switch is much longer on purpose, it acts as the "pulling cord" once you soldered the cable to the battery spring on the contact plate. glue it into the recess and then use the cable loop to pull it in, make sure that the angled legs facing the swith side and that the legs go in between the switch and IR led Properly.

Parts list:
Brass melt heat inserts: 1/4x8x8 double twill
https://de.aliexpress.com/item/1005005083203380.html
Brass melt heat inserts: Length 4mm M2(OD3mm)
https://de.aliexpress.com/item/1005006798286851.html
Brass disc contact plate for battery cap: 20mm diameter
https://de.aliexpress.com/item/1005008782432927.html
Battery assembly screws: M2x6mm
https://de.aliexpress.com/item/1005006968072651.html
Button water resistant: no led if possible/ self locking/ 3-6 volt/ 8mm
https://de.aliexpress.com/item/1005007168217107.html
PVS14 front lens assembly:
https://de.aliexpress.com/item/1005005665744650.html
PVS14 Ocular/ Eye piece:
https://de.aliexpress.com/item/1005006663469240.html
Led "Switch" screw: M3 12mm
https://de.aliexpress.com/item/4000038065691.html
IR illuminator LED: 850nm 5mm
https://de.aliexpress.com/item/32882491556.html
850nm Bandpass filter for IR LED: 6x1mm
https://de.aliexpress.com/item/1005006342091525.html
Battery contacts:
https://de.aliexpress.com/item/1005007104657640.html
Solder wick: 2mmx 1.5meter
https://de.aliexpress.com/item/1005006427770026.html
contact plate screws: M2x4mm countersunk (non metric thread)
https://de.aliexpress.com/item/1005003214170511.html
IR led push button: 4x4x1,5mm
https://de.aliexpress.com/item/1005005633442363.html
Resistor for IR led: 100Ohm 1206 SMT
https://de.aliexpress.com/item/1005009114985699.html
Grub screw for front thread cover: M2,5x3mm
https://de.aliexpress.com/item/1005012143613748.html
Wire: AWG28
https://de.aliexpress.com/item/1005005450270866.html
Metal band for battery contact: Nicel plated steel band 0.12x8mm
https://de.aliexpress.com/item/1005008046854999.html
Brass tube for battery slot: 18x17x500mm OPTIONAL!
https://de.aliexpress.com/item/1005006695881080.html
The MX10160 tube I got for my build:
https://www.alibaba.com/product-detail/MX10160-GEN2-White-P45-Image-
Intensifier_1601665592435.html
PVS14 optics set: Buy front lens and ocular separate to keep within tax free imports!
The combo will cause it to go through customs and you will have to pay additional import tax and fees!!! (depending on where you live)
https://de.aliexpress.com/item/1005005780466031.html
Manual aperture/ focusing iris: