1 / 6
MTG Mana Counter Set — 6 colors, twin-dial — zdjęcie 1
1 / 6

MTG Mana Counter Set — 6 colors, twin-dial

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Snap-together MTG mana / life counters, one per colour (W U B R G C).

Ocena
0 / 5
Polubienia
2
Pobrania
10
Wydruki
0
Wyświetlenia
110
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Board Games
Licencja
Creative Commons — Attribution

Six MTG mana / life counters in one bundle — one per colour (White / Blue / Black / Red / Green / Colourless). Each counter is a small disc with two thumb-twistable dials behind a window: the left dial reads tens, the right dial reads ones, range 00-99. The mana symbol for the colour is engraved into the top face in a contrast colour (looks great with AMS).

Originally built for Magic: The Gathering life tracking and Commander damage, but works for any board / card / RPG game where you need a clicky 00-99 mechanical counter.

What's in the bundle

  • 6 × mana_counter_<c>_half.stl — one per colour (w u b r g c). Each is the full half-shell + its mana symbol pre-aligned in one file.

  • mana_counter_dial_left.stl + mana_counter_dial_right.stl — the same two dials go inside every counter regardless of colour.

  • mana_counter.scad — parametric source if you want to retune clearances, change disc size, or add a custom symbol.

Per counter you print 2 halves of the colour you want + 1 left dial + 1 right dial = 4 parts.

How it goes together (per counter)

  1. Place a left dial and a right dial on a flat surface, digit faces up. The two dials are mirror-pair, so the digit ring on each one is oriented to read upright through its own window.

  2. Drop one half-shell on top of the dials, mana-symbol side up. The dials seat into recessed cavities on the half's inside face.

  3. Flip a second copy of the same half-shell 180° around its horizontal axis (mana symbol now points down) and place it on top of the first. The clamp post and bore on the two halves are intentionally on opposite X positions, so flipping one half lines them up.

  4. Press the two halves together by hand. A 0.25 mm diametral interference + a four-slit slotted bore lets the clamp ridge pop past the bore body with a firm push and a faint click, then the ridge is trapped in the pocket above. Permanent assembly — do not over-tighten in a vise; press by hand. Once snapped, the halves can't separate but the dials inside spin freely.

  5. Twist a dial by grabbing its exposed rim. About a third of each dial's circumference protrudes past the disc boundary so your thumb can engage it directly — no stylus needed.

Repeat for each colour you want from the bundle. The two dials are the same across colours, so for the full set you need 6 left dials + 6 right dials + 6 pairs of half-shells.

Two-colour print (Bambu Studio + AMS)

Each *_combined.stl is an ASCII STL with two named solids in one coordinate frame — the body / wheel as one solid, the symbol / digits as the other. Recipe:

  1. Import a half or dial STL in Bambu Studio (e.g. mana_counter_w_half.stl).

  2. Right-click on the imported model → "Split to Parts".

  3. The two solids become two sub-objects, positions intact.

  4. Assign filament A (body / structural colour) to the body or wheel sub-part. Assign filament B (accent / contrast) to the symbol or numbers sub-part.

  5. Repeat for every combined STL you want to print.

The mana symbols already use the canonical WUBRG colour scheme but the print is parametric — paint them whatever suits your taste.

Why combined STLs? Bambu's "Add Part" workflow re-arranges coordinates, which would put the mana symbol off-centre. Single ASCII STL with two named solids + Split-to-Parts preserves alignment exactly.

Single-colour print (no AMS)

Works fine — Split-to-Parts is optional. Print the combined STL as a single object in any one colour and the symbols / digits show up as crisp engraved recesses instead of inlays. Still very legible, just less colourful.

Print settings

  • Bambu Lab P2S or any 0.4 mm FDM

  • 0.2 mm layer height, 3 walls, 15-20 % infill

  • PLA Basic — works perfectly. PETG also fine.

  • No supports. All overhangs are ≤ 45° including the clamp post.

  • Halves print mana-symbol-face DOWN on the bed so the engraved symbol is the first layer (best surface) and the inside features build up cleanly.

  • Dials print flat on bed, either face down — the digit recesses are symmetric.

Tuning

The default clamp interference is 0.25 mm diametral — "permanent but pushable by hand". If your printer is over-extruding, the halves may not seat fully; back off post_ridge_d from 10.65 down to 10.55 in the .scad and reslice. If they feel loose, push the ridge up to 10.75.

Source

Full parametric .scad is included in the download. Variables at the top control disc size, clamp interference, mana symbol scale, dial diameter, digit font, and number relief depth. Re-export any half with a different colour via:

Fan content for Magic: The Gathering — not affiliated with Wizards of the Coast.

Tagi