Dacia Sandero Stepway III (2021+) - Ceiling Grab Handle Hook
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Custom-designed, sturdy hook for the Dacia Sandero. Installs effortlessly under the original ceiling grab handle screw.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 13
- Wydruki
- 0
- Wyświetlenia
- 131
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
English description first, Slovak translation below.
Designed specifically for the Dacia Sandero Stepway Generation III (models from 2021 onwards).
I created this hook after seeing similar universal/VAG designs, but I wanted a perfect fit for my Dacia. It is engineere
d to mount securely under the ceiling grab handle without requiring any modifications.
Features:
Perfect Fit for Dacia: Tailored for the specific curvature and screw placement of the Sandero III ceiling handles.
Non-Obtrusive: Does not hinder the normal functionality or grip of the grab handle.
Easy Installation: Can be installed in minutes (see instructions below and photo guides).
Strong: Designed to hold a heavy winter jacket or a grocery bag.
Instalácia / Installation Instructions:
Pre montáž budete potrebovať skrutkovač s bitom typu Torx T20. For installation, you will need a screwdriver with a T20 Torx bit.
Preparation (image_4.png): Holding the printed hook near the handle end to check positioning. Note how it sits flush against the ceiling and the handle base.
Removal (image_3.png): Gently pry off the decorative plastic cap from the end of the grab handle.
Unscrewing (image_1.png): Remove the original Torx T20 screw.
Placement (image_6.png): Place the printed hook so its hole aligns with the handle's screw hole.
Fixing (image_1.png): Re-insert and tighten the original screw through both the hook and the handle base.
Finishing (image_7.png): Snap the decorative plastic cap back into place. Your hook is ready!
Demonstration of use (image_2.png): Perfect for hanging your jacket.
Nastavenia tlače (Print Settings):
Materiál: PETG, ASA, or ABS is highly recommended. The interior of a car can get extremely hot in summer, and PLA will melt or warp.
Orientácia tlače: The model can be printed upright as oriented in the STL. This maximizes strength for downward pull.
Výplň (Infill): At least 40% (Rectilinear, Grid, or Gyroid) for necessary strength.
Vrstvy (Perimeters): At least 3-4 perimeters for better structural integrity.
Podpery (Supports): Minimal supports may be needed for the underside of the main hook curve, depending on your printer's bridging capabilities. (My print required minimal supports).
Najprv anglický popis, nižšie slovenský preklad.
Navrhnuté špeciálne pre Daciu Sandero Stepway Generation III (modely od roku 2021).
Tento hák som vytvoril po tom, čo som videl podobné univerzálne/VAG dizajny, ale chcel som, aby perfektne sedel pre moju Daciu. Je navrhnutý tak, aby sa bezpečne pripevnil pod stropné madlo bez nutnosti akýchkoľvek úprav.
Vlastnosti:
Perfektne sedí pre Daciu: Prispôsobený špecifickému zakriveniu a umiestneniu skrutiek stropných madiel Sandera III.
Nenápadný: Nebráni bežnej funkčnosti ani uchopeniu madla.
Jednoduchá inštalácia: Inštalácia je možná v priebehu niekoľkých minút (pozrite si pokyny nižšie a fotonávody).
Silný: Navrhnutý na uchytenie ťažkej zimnej bundy alebo nákupnej tašky.
Inštalácia / Installation Instructions:
Na montáž budete potrebovať skrutkovač s bitom typu Torx T20. Na inštaláciu budete potrebovať skrutkovač s bitom Torx T20.
Príprava (obrázok): Držte vytlačený háčik blízko konca rukoväte, aby ste skontrolovali jeho polohu. Všimnite si, ako je zarovnaný so stropom a základňou rukoväte.
Odstránenie (obrázok): Jemne vypáčte ozdobný plastový kryt z konca rukoväte.
Odskrutkovanie (obrázok): Odstráňte pôvodnú skrutku Torx T20.
Umiestnenie (obrázok): Umiestnite vytlačený háčik tak, aby jeho otvor bol zarovnaný s otvorom pre skrutku v rukoväti.
Upevnenie (obrázok): Znovu vložte a utiahnite pôvodnú skrutku cez háčik aj základňu rukoväte.
Dokončenie (obrázok): Zacvaknite ozdobný plastový kryt späť na miesto. Váš háčik je pripravený!
Ukážka použitia (obrázok): Ideálne na zavesenie bundy.
Nastavenia tlače:
Materiál: Dôrazne sa odporúča PETG, ASA alebo ABS. Interiér auta sa v lete môže extrémne zahriať a PLA sa roztaví alebo zdeformuje.
Orientácia tlače: Model je možné tlačiť vzpriamene podľa orientácie v STL. To maximalizuje pevnosť pri ťahu smerom nadol.
Výplň (Infill): Najmenej 40 % (Rectilinear, Grid alebo Gyroid) pre potrebnú pevnosť.
Vrstvy (Perimeters): Najmenej 3 – 4 obvody pre lepšiu štrukturálnu integritu.
Podpery (Supports): Na spodnú stranu hlavnej krivky háku môžu byť potrebné minimálne podpery v závislosti od premosťovacích schopností vašej tlačiarne. (Moja tlač vyžadovala minimálne podpery).