1 / 5
Eliminate the Ratchet Noise of the Qidi BOX — zdjęcie 1
1 / 5

Eliminate the Ratchet Noise of the Qidi BOX

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Much easier way of converting original annoying ratchet mechanism to a quiet and smoother overrunning clutch mechanism.

Ocena
0 / 5
Polubienia
50
Pobrania
80
Wydruki
0
Wyświetlenia
991
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

The annoying ratchet noise of the Qidi BOX is well known. Personally I had tried to apply grease in the ratchet mechanism to lower the clicking sound. Not really satisfied with the result. It's ok at the beginning. However, the grease will be pushed away while it's running then the clicking sound will come back later. And it'll definately affect loading the filament if I apply too much grease in there.

I didn't want to make a big change on the filament spool drive assembly such as redesigning the active gear or change its structure etc. 3D printing small module gears is troublesome. Those are gonna make things too complicated to implement. 

After further digging into its mechanism, I have come out this super easy solution which is basically a set of jig and a little bushing to help easily converting original ratchet mechanism to a quiet and smoother overrunning clutch mechanism. Meanwhile, this convertion is reversible in case the Overrunning Clutch Bearing was somehow malfunction.

Durability and Stability

Personally I have been testing and using this modification for about one month. Approximately 200 hours printing by using the Qidi BOX. I haven't had any issue so far.

I would hope some one could help to test and let me know if there is any problem. And I'll update my using status as well as some other users who have adopted this solution in China.

BOM

Overrunning Clutch Bearing: HF0306, 3x6.5x6mm (ID=3mm, OD=6.5mm, H=6mm), x4(each BOX)

Note: Overrunning Clutch Bearing also known as One-Way Bearing. It doesn't matter the brand. As long as the spec. 3x6.5x6mm (ID=3mm, OD=6.5mm, H=6mm) matches, it should work fine.

CounterSunk Head Screw: M3x6mm or 8mm, x4 (for the jig mounting)

Nylon/ABS Bushing: Ø3x7x5mm or Ø3x7x2.5mm, x4(each BOX)   (Optional)

Tools

Electric hand drill + Ø6.3mm Drill Bit

Vernier Caliper or Steel Ruler

Rubber Hammer or Bench Vise

Hex Key

How to

The whole process is following here:

  1. Use the drill to enlarge the hole on the Active Gear then insert(interference fit) the Overrunning Clutch Bearing into it. NOTE: Make sure to test the turnning direction first before inserting the bearing as it's really difficult to take it out once it's inserted in!

  2. Place the 3D printed Bushing(or purchased Nylon/ABS Bushing) in between the Active Gear and the fixed ratchet roller to disable the ratchet mechanism.

  3. Reassemble all the parts except the spring since it's no longer needed in the new mechanism.

In this way, the original ratchet mechanism can be converted into overrunning clutch mechanism. However as I have mentioned before, it is possible to recover the ratchet mechanism by removing the bushing and putting the spring back in case the Overrunning Clutch Bearing was somehow malfunction.

The hardest part of the whole process is how to drill a precisely enough hole for the Overrunning Clutch Bearing. The purpose of the Jig Set is to help you precisely enlarge the hole with normal hand drill. It not only guides and centers the drill bit but also controls the deepth of drilling as well.  

Here are the steps and tips on how to drill the hole.

  1. Use the 6.3mm drill bit to polish the inner hole of the Drilling Guider and the Drill Bit Stopper since there are always printing seams.

  2. IMPORTANT! Reinstall the 6.3mm drill bit, make sure the distance between the drill bit tip and the drill chuck is 75mm. Put the Drill Bit Stopper onto the drill bit and push it all the way to the end(drill chuck). Check the distance between the drill bit tip and the Drill Bit Stopper is 40mm.

  3. Mount the Drilling Guider and the Active Gear Drilling Jig_Cover together with four CounterSunk Head Screws(M3x6mm or 8mm). Put the Active Gear into this assembly(it should feel bit tight) and put them on the Active Gear Drilling Jig_Base, there should be no gaps, no big loose.

  4. Drill the hole through the Drilling Guider. DONE!

How to choose the right Bushing?

As far as I know, Qidi BOX has two types of ratchet drive assembly. The difference is on its fixed ratchet roller. One type comes with a boss in the center while another type doesn't. See the picture below.

Choose the Bushing_3x7x2.5mm one for the type with center boss. Choose the Bushing_3x7x5mm one for the type with flat center.

Updates

May 17th, 2026

Uploaded two models:

Active Gear Enhancing Block for One-Way Bearing, this model is for ones who have adopted this modification but worried about the bearing housing cracking and wanted more secured holding of the one-way bearing. 

Active Gear Broken&Fix Block for One-Way Bearing, this model is prepared(as remedial measures) for ones who have adopted this modification, to fix the broken bearing housing just in case. Cut the broken bearing housing(originally spring housing) to apply it.

The blocks are working like clamps to secure the objects. Both of the models need Heat Insert Nut(3x3x4.2mm, x2) and CounterSunk Head Screw(M3x8mm, x2) in order to use. Note, the bigger hole is for Heat Insert Nut.

Working mechanism diagram of blocks.

Further Information (experimenting process and some thoughts)

The reason I chose not to print the gear not only because of 3D printing small module gears is troublesome but also I personally don't really trust the durability and accuracy of 3D printed small module gears based on my existing printing conditions. I think the original gear which was injected through a mold is much better than 3D printed one that I would print. 

Initially, I drilled a through hole by using 6.2mm drill bit on the first testing gear since I wasn't able to control the hand drill once it starts drilling, the bit was just sucked down due to the softness of the plastic. Then I decided to design a jig set to control the drilling. So the second one was well controlled. Then I felt, with 6.2mm housing, the bearing was a little bit tight on the rod. I then used 6.3mm drill bit for the rest of two gears. I wouldn't go for 6.4mm drill bit for mainly two reasons. 1. The bearing housing (used to be spring housing) wall needs to be as thick as possible. 2. The one-way bearing which has been inserted needs to be as tight as possible with the Active Gear. And I think the plastic for the gear is Nylon, it should have enough toughness to hold the bearing not to crack. 

Also, on the first two gears, I actually sanded off the ratchet teeth of the Active Gear to disable its mechanism. The idea of adding bushing came up later.

So basically, the test I am running with my Qidi Box is actually with 3 types of assemblies. One has through hole, 6.2mm bearing housing, no ratchet teeth and no bushing. One has 6.2mm bearing housing, no ratchet teeth and no bushing. Two have 6.3mm bearing housing and 2.5mm bushing. And yes, all of them seem working well so far. However, I haven't tested them in hell mode yet. So I don't know how long they are going to last.

Anyway, personally I don't think the torque of the system is very high. From my testing result so far, the running tolerance seems not too bad. However it's all based on my personal experience and intuition. I don't have any professional device to test it though.

Video Instruction

【【Qidi起迪 BOX】【硬件维护、优化、魔改】棘轮声终极消失术,邪修静静来啦!一刀下去,这个世界从此清静了。。。】

https://www.bilibili.com/video/BV1EjRUBMEyX/?share_source=copy_web&vd_source=002192dc6c65bb1e97d4c22f770216b5

Enjoy!

Tagi