1 / 6
Volvo V70 / S60 / S80 — Drop-in Cupholder (OEM-style) — zdjęcie 1
1 / 6

Volvo V70 / S60 / S80 — Drop-in Cupholder (OEM-style)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

OEM-look drop-in cupholder for Volvo V70/S60/S80. Clamps into the unused coin tray — no drilling, reversible.

Ocena
5 / 5
Polubienia
7
Pobrania
38
Wydruki
1
Wyświetlenia
418
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

Volvo V70 / S60 / S80 — Drop-in Cupholder (OEM-style)

A clean, drop-in cupholder that turns the unused coin tray (muntenbakje) of your 2001-era Volvo center console into a proper can/bottle holder. Designed to look factory once finished — no drilling, no disassembly, fully reversible.


What Fits

Verified to hold:

  • 250 ml slim cans — energy drinks, slim sodas

  • Standard 330 ml / 33 cl cans — soft drinks, beer, regular sized cans

  • Fast-food medium takeaway cups (≈ 0.4 L) — common drive-through size

  • Coffee cups up to 70 mm rim diameter — espresso through medium takeaway, all variants tested

If you regularly drink something else, let me know and I'll measure.


Fit & Compatibility

  • Verified: Volvo V70 (2001)

  • Should fit: Volvo S60 and S80 of the same generation — shared center console platform

  • Mounts in: the rectangular console compartment without a lid (the coin tray slot, next to the lidded compartment)

  • Mounting method: clean clamp-fit using the slot's existing geometry. No screws, no adhesive, no trim removal.

  • Reversible: pops in and out at will

Heads-up: these consoles are 25+ years old. Tolerances drift with age, heat cycles, and previous owners. Always do the vase-mode test print described below before committing to a full print.


Two Variants — pick what fits your patience

A. Two-piece design (recommended for OEM look)

Top and bottom print as separate parts, then snap together.

The trick: print the top piece upside down. That way the first layer becomes the visible top surface. If your first layer is dialed in, the finished part has a clean, smooth top — exactly the surface that catches the eye in the console.

  • Cleaner aesthetic

  • Better surface for sanding + painting if you want full OEM-grade finish

  • Slightly more assembly

B. Single-piece variant (just want it done)

Print, drop in, done.

  • Faster

  • One file, one print

  • Aesthetic is acceptable but won't reach the same finish quality as variant A


Print Settings (recommended)

  • Material — read carefully, this part lives in a hot car:

    • ABS or ASA: recommended (minimum). Car interiors easily pass 50 °C in summer, often higher. ABS/ASA handles that without softening. ASA has better UV stability if relevant; ABS is fine for this hidden, low-stress location. Yes, you'll deal with warp and fumes during printing — that's the price of a part that survives the dashboard. The displayed and verified model is printed in Polymaker ASA.

    • CF-filled variants (PETG-CF, ABS-CF, etc.): even better if you have them. Lower thermal expansion, higher dimensional stability, less warp risk over years of heat cycles. Worth the abrasive nozzle wear for a part that lives in a heat box.

    • PETG: questionable. Better than PLA, but sustained summer interior temps can still soften it under load. Acceptable in a garaged car. Not recommended if it bakes in direct sun.

    • PLA / PLA+: don't. A parked car already passes PLA's softening point on a 20 °C day with sun. It will warp eventually. Earlier iterations of this design that were printed in regular PLA are now repurposed as plant pots (plantenbakjes) — they survive in the garden, not in the dashboard.

  • Layer height: 0.20 mm standard, 0.16 mm for the top piece if you want a finer visible surface

  • Walls: 3+ perimeters

  • Infill: 15–20% is enough — this part isn't load-bearing

  • Supports: not required if you follow the print orientation (top piece upside down)

  • Bed adhesion: glue stick / 3DLAC / brim — your preference


Critical Fit Check — Vase Mode Test First

Before you commit to a 1–2 hour full print, do this:

  1. Slice the cupholder body in vase mode (single-wall, hollow)

  2. Print just the outer rim/clamp section (~5–10 minutes)

  3. Drop it into your console slot

  4. Verify clamp engagement and ring fit

If it's loose or too tight, scale ±0.5–1% in your slicer and retest. 5 minutes saved you 90 minutes.

This step is non-negotiable on aging cars. Same car model, same year, different console fit.


Optional: Finishing for Look

Two paths depending on how much effort you want to invest.

Path A — Paint pipeline (OEM-look)

If you want it to disappear into the console (literally — visually indistinguishable from factory):

  1. Print (variant A, top piece upside down)

  2. Light sanding on visible surfaces

  3. Plastic primer

  4. Matte black spray paint (texture-matched to console plastic)

The texture and matte finish blend with the surrounding factory plastic. Done right, you'll forget it's a print.

Path B — Vinyl wrap (faster, no paint mess)

If paint isn't your thing, a cheap carbon-look vinyl wrap works surprisingly well — see the photos. Couple of euros worth of wrap from any auto shop or AliExpress, ten minutes with a heat gun or hair dryer, and the print lines disappear under the texture. Bonus: easy to redo if you want to change the look later.

Works best on the single-piece variant or the assembled two-piece — wrap the visible top surface, hide print lines, done.

Pick the path that matches your patience level and aesthetic preference. Both look intentional.


Files

  • cupholder_top.stl — top piece (variant A, print upside down)

  • cupholder_bottom.stl — bottom piece (variant A)

  • cupholder_singlepiece.stl — variant B (one-shot)

  • vase_test.stl — outer rim only, vase mode (fit check)


Note on Photos

The staged product shots have been color-corrected and cleaned up with AI tools (lighting, background). The part itself is real — it took many iterations to get right. The geometry is unedited: what you print is what you see. The in-use shots (with the actual can / cup / car interior) are processed.


Notes from the Designer

This was made for my own daily V70 because the unused coin tray is wasted space and a Red Bull can in the cup holder slot beats a can rolling around the footwell.

Two-piece + paint pipeline took the part to factory-look in my own car. The single-piece variant exists because not everyone wants to sand and paint a £4 print — sometimes "works and stays put" is the whole spec.

Feedback welcome. If you adapt this for another Volvo model with the same console, let me know — happy to link variants.


Tags: volvo, v70, s60, s80, cupholder, drop-in, console, oem, automotive

Tagi