Makita Router Jig for Shallow Bowls / Dish Routing Jig
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Simple router jig for creating smooth shallow bowls in wood. Adjustable depth and surprisingly clean results.
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 262
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution
With this jig, you can route shallow bowl-shaped recesses into wooden boards in a few simple steps.
I originally designed it for a rocking knife cutting-board, because nuts and other food kept rolling away while chopping. With this shallow bowl shape, everything stays nicely contained until it is fully chopped.
The jig consists mainly of two parts. One to which router is attached to and which does have a 8mm threaded rod. This part is pivoting in the top and can be lowered stepwise.
The mounting system is designed for a Wabeco drill stand, although it could probably be adapted to other systems. A stable drill stand is highly recommended, since it allows precise height adjustment. Fine adjustment is done with the star knob. The small nut acts as a lock nut, preventing the star knob from turning after adjustment.
The star knob has 5 arms. With an M8 thread (1.25 mm pitch), each 1/5 turn changes the height by approximately 0.25 mm.
I achieved good results by reducing the height by a maximum of 1.25 mm per routing pass.
Do not forget to secure the M8 screw with a nut from above the plate it sits in — I forgot this during my first test run and it is not visible on the pics.
The jig is designed for a Makita router with a 65 mm diameter motor housing (probably others work aswell). I intentionally used a relatively small router bit (approx 12mm diameter) to reduce cutting forces and avoid visible ridges in the surface. You do not want it too small too...
The resulting bowl has a radius (depthwise) corresponding to the height of the ball joint center. The smallest achievable radius is about 28 cm before the router holder collides with the suspension.
I was honestly surprised how clean the results turned out.
I moved the router slowly in a clockwise spiral from the outside inward, removing material layer by layer.
Assembly; You will need:
M8 screw long (3x M8 Nuts)
6x M4, 2x M4 Wingnuts and 4x M6 screws
4x M4 and 4x M6 threaded inserts (I used Turmberg3D inserts)
washers
If you do not want to use threaded inserts, all holes are through-holes, so sufficiently long screws or threaded rods can do the job.
Practical Recommendations
Secure everything firmly.
The drill stand must be rigidly mounted.
The workpiece must be clamped securely.
Before starting, make sure enough M8 thread remains available above the top to reach the desired final depth.
Mark the target center point on the board and align the router carefully before starting. I adjusted the alignment slightly again after the first pass, once the routed bowl became visible.
When switching on the router, ensure the bit is clear of the wood by pivoting the router sidewards. You do not want to start it when it touches the wood.
I start in the air and slowly let the running bit touch the board outside of the already routed area. Interestingly, I achieved the best results by moving the router clockwise (which is technically the “wrong” direction), slowly inwards in a spiral with reducing diameter. This produced a much smoother and more controlled cut. Counterclockwise motion caused the router to grab more aggressively and resulted in uneven surfaces.
Let the router stop completely before adjusting height
Reduce depth by no more than 1–1.25 mm per pass (lock the star knob with the second nut)
My router bit was about 12 mm in diameter. Much smaller bits may make smooth cutting difficult. I have not tested larger bits.
I strongly suggest trying the jig on a test board first.
Do not rush, take your time, it is a very interesting to do process.
Jigs always have their quirks — make sure you fully understand what you are doing. This is not a beginner woodworking project.
Printing
PETG recommended
4 perimeters (for strength and possible drilling/rework of holes)
7 top & bottom layers
0.2 mm layer height
No supports
20% infill
I’d love to hear about your experience with the jig, or get some recommendations on how to use or improve it.