1 / 7
Toyota MR2 SW20 Fog light housings - Restore damaged fog lamps — zdjęcie 1
1 / 7

Toyota MR2 SW20 Fog light housings - Restore damaged fog lamps

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Files to print a full replica of MK2 MR2 front fog lamp. Including files to recreate the aim adjustment mechanism

Ocena
0 / 5
Polubienia
6
Pobrania
55
Wydruki
0
Wyświetlenia
229
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

Like many SW20 MR2 owners, as I stripped my car down for restoration, the fog lamp screws were seized in place. Removing the lights meant a couple of the mounting tabs on the lights where damaged. Rather than attempting to repair the tabs, I decided to print an entire new housing instead. I then transplanted all the usable parts from the original lamps to the new housings.

I’ve created two versions, one that replicates the factory assembly entirely, and one that is adjusted via removing the lamp. I printed mine in in ASA but PETG might be okay if you don't have a printer that can print ASA. Hopefully this will help others repair their broken fog lights as I have done with mine.

Disassembly process for original fog lamps

First remove the rear cover cap and bulb. Then remove the aim adjustment assembly. This is held to the housing with two screws, I ground the heads off the screws on my lamps as they where heavily corroded.

Next the glass needs to be removed from the housing

The glass lens is held in the housing with two steel clips, and then a bead of black sealant. The sealant is extremely strong and make removing the glass difficult.  The best method I found was to place the fog lamp in a cardboard box and heat the it up with a heat gun. An alternative would be to use an oven. Try to get the assembly nice and hot as to soften the adhesive. I then used a combination of pry tools around the edge, and pushing the glass from behind through the cover hole on the back of the assembly. Try and avoid using anything metal to pry on the glass is it’s very brittle and can easily chip.

Once the glass is removed the reflector inside can be accessed. This is held in by three points, two ball joint style clips at the bottom and the aim adjustment screw at the top. Firstly, back off the adjustment screw from the back of the assembly all the way, then carefully pry the reflector forwards. It should pop away from the bottom clips and come away.

The wiring connector can then be de-pinned, the wiring passed through the hole at the rear and the reflector removed fully.

The adjustment screw is encapsulated into the housing with a star washer. With the reflector removed this can be prised off and removed.

The final few pieces of hardware can then be removed from the housing. You should then be left with everything needed to rebuild the fog lamp.

Cleaning the glass

Once removed the glass will still have a large amount of remaining adhesive around the edge. This can be tedious to remove. To remove it, I used a sink full of hot water to soften it, then scraped it off with a wire wool scouring pad. I then removed the last remnants with panel degreaser as it’s quite sticky.

Reassembly

Assembly is the reverse of disassembly. See the PDF diagram for the adjustment mechanism assembly. The M3 and M4 screws are tapped directly into the print. I used butyl tape to reseal the glass into the housing. Ensure the assembly is full completed and the glass fits nicely into the housing before sealing it back in as it's a pain to undo once seated.

Parts lists (per fog lamp)

With external adjustment

-Printed housing x1

-Printed inner gear housing x1

-Printed outer gear housing x1

-Printed Adjustment gear x2 (printed on 0.2mm nozzle)

-Printed Adjustment gear outer x1 (printed on 0.2mm nozzle)

-Adjustment shaft x1

-8mm O-ring x1

-6mm star washer x1

-12mm M3 countersunk bolts x4

-12mm M4 caphead bolts x2

Without external adjustment

-Printed housing x1

-Printed manual adjustment knob x1

-8mm O-ring x1

-6mm star washer x1

Tagi