1 / 8
Guitar Pedalboard System for Common 1.5" x 1" Board — zdjęcie 1
1 / 8

Guitar Pedalboard System for Common 1.5" x 1" Board

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Combine 1.5" x 0.75" boards with 3D printed supports to create a strong and affordable custom-sized pedalboard.

Ocena
0 / 5
Polubienia
6
Pobrania
36
Wydruki
0
Wyświetlenia
459
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Music
Licencja
Creative Commons — Attribution — Noncommercial

Cheap, Custom Pedalboards

Sometimes labeled as 2" x 1" boards, these 1.5" (actual width) x 0.75" (actual thickness) boards are sold at many home improvement stores in packs of 4 in 48" length, but you can use any dimensional lumber that fits the criteria of actual 1.5" x 0.75".

3-Slat and 4-Slat Options

The 'small' supports use 3 slats and the 'large' supports use 4 slats. The small supports will fit standard compact pedals with some room to account for connectors so that they do not hang off the front or back. The large supports are better for those using medium-large sized expression pedals (though some will hang off a bit still) and some multi-effects units.

Support Hardware

I recommend #4 or #6 (possibly even #8) wood or sheet-metal screws. USE WASHERS as shown in the photos or you're going to have a bad time. 1/2" length is ideal. The slats I used had no problem, but if you are concerned about splitting you may want to drill pilot holes before using screws. 

Anti-Skid Feet

The softer the TPU is, the better the grip will be. 95A is ubiquitous and works great. I used M3 screws directly into the PLA to mount these, but you could certainly sink some brass heat-set inserts if you want to make it more robust.

Risers

For those that want to add a second level, you can print the riser as many times as you need. They are designed to work in pairs, one on each side of a slat section, at any length of your choosing. In the photos, you can see that I am using one pair of riser brackets to elevate my M-VAVE Chocolate Plus behind the HX Stomp. You could use these in parallel to create 2-4 slat riser platforms. 

Riser Hardware

M3 screws and nuts are used to keep the size down. Tighten in alternating pattern, a little at a time on each side, until the riser is locked down around the slat. The throat size on these riser brackets are meant to accommodate the slat + velcro with a little space to allow for tension/better grip. If you've got velcro installed on the board, you do not need to wrench these down in order for them to hold, especially if you're doing 2+ slat risers and bridging them with pedals (which act as reinforcement when on the board). Overtightening will result in the ears cracking. 

Cable Tie-Down Points and Pedal Mounts

The cable tie-down points are straight-forward; Put them wherever you want. They have countersunk screw holes if that's something you want to take advantage of. I ended up not using them in my final board and just wrapped the velcro ties around the slats themselves, but I uploaded these just in case.

If you want to mount a pedal down with screws (like I did with this MXR power supply), you can use the two-ring 'grommet' type mounting ears. They should be printed with TPU for flexibility and strength. Two different sizes included, the larger will be the more useful for most applications. (Ignore my "oops I screwed these in at the wrong place" mess-ups in this photo).

Input Jack Mount

This one may or may not be useful for many of you, but I happened to have a 1/4" Female-Female adapter laying around and decided to use the hexagon shaped hole on the side of the supports to turn it into an input jack. Print two of these half-hexagons, clamp them around the adapter, screw them into the support. If you want to use this, you may have to either edit the file or perhaps wrap your adapter with electrical tape to increase the grip such that it doesn't move when being unplugged/plugged in. 

Material Considerations

With the exception of the two-ring pedal tie mounts (which use TPU), I used PLA for all parts for maximum static strength. 

  • Material

    • Feet and "Two-ring" pedal tie mounts: TPU

    • Everything else: PLA (normal or strong PLA, matte "PolyTerra"-like material isn't as strong)

  • Layer Height: 0.2mm

  • Strength: 

    • Supports: 6 walls, 50% infill or more recommended. You're going to be putting your body weight on this, so make sure you're using a lot of reinforcement.

    • Recommend Gyroid infill pattern

    • Feet: 2 walls, 25% infill should work fine

Disclaimer

This isn't perfect. I really just made this for myself to fit my own needs and thought someone else might find it useful. You may need to use your imagination to get it to work for you. If you use this system to build your own board, I would love to see it posted here as a make.

Tagi