Markforged Kinematics V2.0 for FlyingBear Ghost 5
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Markforged Kinematics V2.0 Upgrade for Flying Bear Ghost 5
- Ocena
- 0 / 5
- Polubienia
- 15
- Pobrania
- 36
- Wydruki
- 0
- Wyświetlenia
- 357
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
Upgrade your Flying Bear Ghost 5 with a lightweight and rigid Markforged-style kinematics system. This modification replaces the stock motion assembly with a proven parallel-rail design inspired by Markforged printers, improving belt routing, reducing moving mass, and increasing overall motion stability.
Features
Markforged-inspired XY kinematics
Compatible with Flying Bear Ghost 5
Lightweight moving assembly
Improved rigidity compared to the stock mechanism
Optimized belt routing for smooth motion
Required Hardware
Bearings & Motion Components
Part | Quantity |
|---|---|
F623ZZ Flanged Bearing (3×10×4 mm) | 4 |
GT2 Pulley 20T W6 B4 (18×8.5×12 mm) | 4 |
GT2 Belt 6 mm (1280 mm or longer) | 1 |
Heat-Set Inserts
Part | Quantity |
|---|---|
M3 Brass Heat-Set Inserts (Ø4.6 × 5.7 mm) | 32 |
Pins
Part | Quantity |
|---|---|
D2 × 15 mm Pin | 2 |
D3 × 15 mm Pin | 2 |
D4 × 16 mm Pin | 2 |
D4 × 20 mm Pin | 1 |
D4 × 25 mm Pin | 3 |
Fasteners
Part | Quantity |
|---|---|
M3 × 5 mm Socket Head Screw | 14 |
M3 × 10 mm Socket Head Screw | 12 |
M3 × 15 mm Socket Head Screw | 11 |
M3 × 16 mm Socket Head Screw | 2 |
M3 × 30 mm Socket Head Screw | 2 |
M3 × 8 mm Countersunk Screw | 2 |
Recommended Print Settings (Cura)
Setting | Value |
|---|---|
Nozzle Diameter | 0.4 mm |
Layer Height | 0.15 mm |
Line Width | 0.4 mm |
Infill Line Width | 0.45 mm |
Wall Thickness | 2.0 mm |
Top/Bottom Thickness | 2.0 mm |
Infill Density | 30% |
Infill Pattern | Cubic |
Connect Infill Lines | Enabled |
Print Speed | 30–50 mm/s |
Printing Recommendations
Print structural parts with at least 30% cubic infill.
Use PC, ABS, or ASA for better durability and heat resistance.
Install all heat-set inserts carefully to ensure proper alignment.
Check bearing and pulley fitment before final assembly.
Verify belt tension after installation for optimal print quality.
Assembly Notes
Install all M3 heat-set inserts before assembly.
Press-fit the pins into their designated locations.
Mount the F623ZZ bearings and GT2 pulleys.
Assemble the gantry and carriage components.
Route and tension the GT2 belt.
Verify smooth movement across the entire travel range before powering the printer.
If you build this upgrade, feel free to share your makes and improvements. Feedback, remixes, and assembly photos are always welcome!