1 / 5
Prusa CORE One L MMU Enclosure (ready to print) — zdjęcie 1
1 / 5

Prusa CORE One L MMU Enclosure (ready to print)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Prusa CORE One L MMU Enclosure (ready to print)

Ocena
5 / 5
Polubienia
10
Pobrania
49
Wydruki
0
Wyświetlenia
392
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

While INDX is not (yet) available for Core ONE L, I had to install the MMU3. Due to the fact that there is no buyable Enclosure from Prusa available, I modified the Prusa Original C1L_MMU_ENCLOSURE_R1 and C1L_MMU_holder_R1 to make them ready to print.

Option 1 (Enclosure only)

To Print:

  • 1x Core ONE L MMU Enclosure R1 Part 1

  • 1x Core ONE L MMU Enclosure R1 Part 2

  • 1x Core ONE L MMU Enclosure R1 Part 3

  • 1x Core ONE L MMU Enclosure R1 Part 4

  • 1x Core ONE L MMU Enclosure R1 Part 5

  • 1x Core ONE L MMU Enclosure R1 Part 6

  • 1x Core ONE L MMU vent R1 modified

  • 1x Core ONE L MMU Holder R1 Part 1

  • 1x Core ONE L MMU Holder R1 Part 2

  • 2x TOP_COVER_LOCK_R1 (Prusa Original Part)

  • 2x TOP_COVER_HOLDER_R1 (Prusa Original Part)

  • 2x VENT_NUT_R1 (Prusa Original Part)

  • 2x MMU_holder_R1 (Prusa Original Part)

Print Settings:

  • 0.4mm Nozzle

  • Material: Prusament PETG or better

  • Print Settings: 0.2mm STRUCTURAL

  • Layers and perimeters

    • Perimeters: 3

    • Seam Position: Nearest

  • Support material

    • Auto generated supports: yes

    • Overhang treshold: 39°

    • First layer expansion: 1mm

  • Prusa Original Parts shall be printed according Prusa's recommendation

Additional parts required:

Printed parts preparation:

  1. Mount Aluminium Strip Brush 40mm x 160mm into Core ONE L MMU Enclosure R1 Part 1 (optional)

  2. Glue and Screw Core ONE L MMU Enclosure R1 Part 1 and Core ONE L MMU Enclosure R1 Part 2 together. Use 3x Screw DIN 912 M4x16 and 3x Nut DIN 934 M4.

  3. Glue Core ONE L MMU Enclosure R1 Part 3, Core ONE L MMU Enclosure R1 Part 4, Core ONE L MMU Enclosure R1 Part 5 and Core ONE L MMU Enclosure R1 Part 6 together

  4. Glue the two subcomponents together.

  5. Glue and Screw Core ONE L MMU Holder R1 Part 1 and Core ONE L MMU Holder R1 Part 2 together

  6. Follow the original installation similar to Top Cover Preparation and MMU3 for CORE One L.

Option 2 (Enclosure with Servo Driven Chamber Ventilation)

To automatically open and close the Vent Cover on the Prusa CORE One L with MMU3, a servo, which is connected via the Prusa “Hackerboard” to the Prusa CORE One L, was added. Via a GCODE the Vent Cover can be opened and closed during the print.

WARNING: This MOD is supplied as is and you build it at your own risk. I will NOT be responsible for any damage or injury to you or your property that may occur. 

Execute all steps from Option 1

To Print:

  • 1x Servo Horn

Print Settings:

  • 0.25mm Nozzle

  • Material: Prusament PETG or better

  • Print Settings: 0.12mm STRUCTURAL

  • Layers and perimeters

    • Seam position: Nearest

  • Infill

    • Fill density: 100%

    • Fill pattern: Rectilinear

  • Skirt and brim:

    • Brim width: 5mm

Additional parts required:

Assembly Instructions:

  1. Buy and print all the required parts, as listed above

  2. Install the Prusa GPIO “Hackerboard” set

    1. It is recommented to solder the Pitch Pin Header to the Prusa GPIO Hackerboard

  3. Connect the Prusa GPIO Hackerboard with the BIFRC Servo Trigger Module with the two Jumper Wires (see wiring diagramm):

    1. PRUSA GPIO Hackerboard PIN GND (Ground) → BIFRC Servo Trigger Module Ⓖ (Ground) 

    2. PRUSA GPIO Hackerboard PIN 7 → BIFRC Servo Trigger Module ①

  4. Connect the USB Type C to 2 USB Type C Splitter to the USB Type C Plug of the printer or a USB-Charger (if needed)

  5. Connect the Cable of the Camera (it there is any) and the USB Type C Cable 15cm to the USB Type C to 2 USB Type C Splitter

  6. Connect the USB Type C Cable 15cm to the BIFRC Servo Trigger Module (see wiring diagramm)

  7. Put the Double Sided Adhesive Tape on the back of the Servo Support

  8. Mount the Micro Analog Servo EMAX ES08MA II with two 2mm Cross Phillips tapping Screw to the Servo Support

  9. Mount the Servo Horn to the Micro Analog Servo EMAX ES08MA II with the original Servo Screw

  10. Mount the Brass Insert Nut M3x5 into the Core One MMU3 Vent Cover

  11. Replace the original Core One MMU3 Vent Cover with Core One MMU3 Vent Cover (use the original M3x10Tr Screws (2x), Vent Nut (2x) and O-Rings(2x))

  12. Tape the Servo Support to the MMU Top Cover

  13. Mount the Push Rod 80mm to the Servo Horn and the Core One MMU3 Vent Cover

  14. Add the Screw DIN 912 M3x10 to the Brass Insert Nut M3x5

  15. Connect the Micro Analog Servo EMAX ES08MA II via the Servo Extension Cable 60cm to the BIFRC Servo Trigger Module

  16. Align the Push Rod 80mm/Servo position correctly and tighten the Screw DIN 912 M3x10

  17. Set the correct Mode on the BIFRC Servo Trigger Module

  18. Perform a proper wiring, use the Mini Cable Winder Organizer

  19. Add the following GCODE to your Prusa Slicer

GCODE that needs to be added to the "Start G-Code" Section in Prusa Slicer:

; Automatic Chamber Vent Control
{if filament_type[initial_tool] =~ /.*(PLA|PETG).*/}
M262 P7 B0
M264 P7 B1
{else}
M262 P7 B0
M264 P7 B0
{endif}

GCODE that needs to be added to the "End G-Code" Section in Prusa Slicer:

; Automatic close the Chamber Vent if it was opened
{if filament_type[initial_tool] =~ /.*(PLA|PETG).*/}
M264 P7 B0
{endif}

see also Prusa CORE One L Buffer Plate (ready to print)

Tagi