1 / 3
Tool Organizer with Cutout for Prusa i3 MK2 MK2S LCD — zdjęcie 1
1 / 3

Tool Organizer with Cutout for Prusa i3 MK2 MK2S LCD

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

WARNING: This is at LEAST a 48 hour print,will require a large build surface (roughly 200mmx200mmx200mm) and will use…

Ocena
0 / 5
Polubienia
3
Pobrania
10
Wydruki
0
Wyświetlenia
357
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

WARNING: This is at LEAST a 48 hour print,will require a large build surface

(roughly 200mmx200mmx200mm) and will use up about 500g of filament.

This is a tool organizer for the items I use with my printer. This is a bit specific to my tools but maybe someone else can use it too. It features slots for the following tools specifically:

E3D Nozzle Cross Wrench: https://www.filastruder.com/products/e3d-nozzle-spanner-wrench

Foreasy 3D Printer Tools: https://www.amazon.com/gp/product/B01A81FXMK/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

BuildTak BT30185 Spatula: https://www.amazon.com/gp/product/B017XGEDOM/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Gizmo Dorks 3D Print Removal Tool: https://www.amazon.com/gp/product/B01DTLWVSU/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

Super Lube 21030 Synthetic Grease: https://www.amazon.com/Super-Lube-21030-Synthetic-Grease/dp/B072QW3LG7/ref=sr_1_6?s=industrial&ie=UTF8&qid=1502332625&sr=1-6&keywords=super+lube

Brass Brush: https://www.amazon.com/gp/product/B019HPVULQ/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

It also has three pockets for generic stuff like pliers, flush cutters, tweezers, wrenches, etc.

The LCD shown is the LCD that comes off the Prusa, All I did was unclip the zip ties leaving the brackets attached so it sits on a table. The tool organizer prints with a cavity for it to sit over the LCD casing. I opted to superglue it in the cavity being mindful of where the SD card slot is to make it one solid unit.

Print Settings

Printer Brand:

Prusa

Printer:

Prusa Mk2

Rafts:

No

Supports:

Yes

Resolution:

.20

Infill:

5%

Notes:

Supports are a MUST to make the cavity for the LCD. Play around to make a support pattern that you think is best. I did mine diagonally so that the bridge is well supported. Infill is super low to save plastic. I used honeycomb. Be aware that you may need many top layers due to the low infill. I have some minor errors in the bottom of the pockets where the edges have holes. I think its due to the low infill but not enough top layers to properly seal it. Still perfectly functional for what its for.

Category: 3D Printer Accessories

Tagi