Yamaha XV950R / Bolt Air Cleaner Assembly for generic HD-0800 filters
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
XV950R quick-fit forward-offset air cleaner assembly with additional parts to allow use of cheaper filters.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 14
- Wydruki
- 0
- Wyświetlenia
- 149
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Vehicles
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a remix and a build upon the excellent forward air cleaner mod for the Bolt posted by Uglylittlebush.
I have remixed the original adapter which gets bolted to the air intake, as the crankcase breather port position wasn't in the right place and I didn't want to start dismantling the bike or cutting hoses. I moved the port down and to the right, which is very close to its position on the standard air cleaner box. So replacing it is now really quick and easy and no awkward hose re-routing is needed.
There seem to be two types of HD-0800 29442-99X filter copies. One, as used by Uglylittlebush, appears to have an integral steel cover plate on the top, but only comes in blue unless you spend a lot of money. The other has a loose steel cover plate but comes in several colours. I wanted black, so I had to go for the latter, which meant I needed to modify the original scheme so that I could secure the steel cover plate onto the air filter element. I also needed a bespoke decorative outer cover as a result of the other design changes.
I used the following additional parts
The two gaskets from Uglylittlebush's design (copies below)
1 off M5 SS cap head screw 12 mm
2 off M5 SS cap head screw 16 mm
Aluminium tape to cover redundant holes on steel cover plate
1 off M6 x 50 mm SS bolt (may need to be cut short depending on whether a dome nut or thumb nut is used to hold things together)
M6 SS thumb-nut or dome nut
Loctite 222 thread-locker
The adapter, cover retainer and outer cover are printed in PETG. I printed the first two with quite dense infill to impart toughness.
The M6 adaptor is printed in TPU to give some grip to the internal taper, although PETG might work. The gaskets were printed in TPU.
My fitting sequence was as follows:
Remove old air cleaner box and keep it safe somewhere (for if the bike is sold)
Fit TPU gaskets to offset adapter. Attach the crankcase breather hose to the port on the rear of the offset adapter, which is then bolted onto the bike's air intakes using three M5 screws. The shorter one goes on the left. I used lithium grease on the threads.
Remove the steel filter cover plate before applying filter oil to the filter element
Stretch the filter element over the offset adapter. I found this was easier if the rubber was warmed up.
Assemble the M6 bolt into the M6 adapter then poke it through the cover retainer and press it into position.
Put the cover retainer with bolt inside the air filter, so that the bolt is sticking outwards.
Cover the three outer holes in the steel filter cover plate with aluminium tape and fit it loosely over the top of air filter element, taking care not to push the M6 bolt back inside the filter.
Fit the outer cover over the M6 bolt and fit the thumb-screw onto the end of the bolt for a couple of turns to stop it all falling apart. Then the steel filter cover plate is pressed fully onto the top of the air filter element. Then the outer cover is aligned and the thumb-nut is tightened up fully (with a little thread-locker for good measure), to pull everything together.
So far it is all holding up well, it sounds fantastic and has survived several long runs. I didn't do a ECU remap and have seen no ill effects. In any case, if you duplicate this work and fit it to your bike, you do so at your own risk.