1 / 3
Ender 3 v3 SE runout sensor extruder cover — zdjęcie 1
1 / 3

Ender 3 v3 SE runout sensor extruder cover

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Orientacyjna cena wydruku pliku

5,46 € – 6,67 € netto (bez VAT)

Dla pliku: ender3v3se-filasensor-mount.gcode

To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.

Plik i założenia wyceny

Plik użyty do wyceny

Średnia wycena orientacyjna: 6,07 € netto (środek widełek).

Masa podana przez autora
46 g
Czas druku podany przez autora
7,5 godz.
Materiał u źródła
PLA
Materiał wyceny
PLA
Drukarka wyceny
Bambu Lab P1S - 0.4 nozzle
Proces wyceny
0.20mm Standard

Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.

Zapisane na tym urządzeniu.

Original extruder cover modded to add holder for IdeaFormer (or any compatible) runout sensor.

Ocena
0 / 5
Polubienia
3
Pobrania
14
Wydruki
0
Wyświetlenia
176
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Original Ender 3 v3 SE extruder cover to allow installing a filament runout sensor right above. This minimizes the length of the run filament has to make between the sensor and feeder. When there's filament there but none in the sensor, the print is paused, after which you have to push new filament all the way through that run. Traced around Meerkat's model.

Printing:

I printed this with the staggered vent holes on the build surface, layer height 0.2mm, variable layer height set all the way Smooth, tree supports enabled (I'd recommend Tree Strong if you have the time and filament - Default and Tree Hybrid are weak enough to crunch while printing and possibly affect outer wall printing quality), 10% Gyroid infill. I printed on the Ender 3 v3 SE in PLA. Took about 7.5 hours.

Assembly

Required hardware: 2x M3 heatset brass inserts, 2x M3 screws long enough to clear the sensor's holes and have some length left over, optionally 2x washers with M3 hole. You will also need to make an adapter cable.

  1. Drive the inserts in with a soldering iron or similar tool from the opposite side from the angled support. Be careful not to melt the support if you have a long skinny tip.

  2. Run "Control > Retract" on the printer, remove the created blob and power the printer off.

  3. Take off the original extruder cover using the second smallest Allen key included with the printer.

  4. Unscrew the fan that's attached to the cover.

  5. Install the fan onto the new cover. Note that short screws go in the long posts, long screws go in the short posts. The airduct must be on the same side as the short posts.

  6. Install the runout sensor now as the extruder's ribbon cable will obstruct screwing it in later. Align the screw holes and make sure the sensor's filament tube is near the center of the cover (not facing away from it; see image). If available, put washers on sensor (on the side that's farther away from the front of the cover). Screw in using 2x M3 screws.

  7. Align the new cover with the extruder assembly (make sure the screw holes and pegs at the back match with it) and screw it in using included Allen key #2.

  8. Create and connect the adapter cable. Instructions detailed below.

  9. Power on the printer and try any print without loading filament. If the screen suddenly switches to Homing. No other operations are allowed, that's good. It means the sensor is working correctly. In that case, you are done!

Adapter cable

So Creality did something really weird with the filament sensor cable. The motherboard has a 4-pin socket, but the sensor has a 3-pin socket. Their official adapter cable, which as far as I can tell cannot be purchased separately, just leaves the fourth pin of the motherboard-side plug empty (not even a crimped connector inside). Additionally, this kind of connector (JST-XH) will not fit through the small hole in the printer's base under one of the gantry's extrusions, so if you want to use the built-in cable management space there, you have to make an even more complicated adapter.

Option A: through cable gap

In the base of the printer behind the right extrusion of the gantry, there is a rectangular pop-out hole. Break that (push using e.g. a screwdriver or cut with pliers). You will need:

  • JST-XH 4-pin male connector with wires

  • JST-XH 3-pin male connector with wires

  • Heat shrink of sufficient length and width to put onto wires of connectors

  • Total cable length must be about 50cm. If your JST pigtails aren't long enough, use some extra wire.

Now, let's make the cable:

  1. Grab the 4-pin connector so that the arrow-shaped protrusions face toward you and point up. Pull out the right-most wire as it is not needed.

  2. I'll assume the 4-pin's wires are red-yellow-black-black and 3-pin's yellow-black-red (both read left-to-right with arrows facing toward you and pointing up). Place some heat shrink on each wire on just one of the pigtails. Solder red with red, yellow with black, black with yellow. Shrink the heat shrink with a heat gun or lighter.

  3. Power the printer off and turn it around so that the bottom side is accessible. Unscrew it.

  4. Run the newly-created cable through the hole. Plug the 4-pin end into the motherboard. The socket you need should be labelled "FILAM" and located near a big set of green screw terminals going to the PSU.

  5. Plug the sensor's end in. Jump to step 9 of assembly instructions.

Option B: through gantry extrusion

The left extrusion of the gantry is hollow for cable management. I'm pretty sure this is intended for the LED Light Bar, but you can run the sensor cable through there just fine. You will need:

  • JST-XH 4-pin male connector with wires

  • JST-XH 3-pin male connector with wires

  • JST-ZH 3-pin male connector with wires

  • JST-ZH 3-pin female connector and wires you can solder onto it

  • A total length must be about 90-100 cm. If your JST pigtails aren't long enough, use some extra wire.

The ZH connectors are necessary because the hole in the base of the printer under the extrusion will not fit JST-XH. Now, let's make the cable:

  1. Grab the 4-pin connector so that the arrow-shaped protrusions face toward you and point up. Pull out the right-most wire as it is not needed.

  2. I'll assume the XH 4-pin's wires are red-yellow-black-black, XH 3-pin's yellow-black-red (both read left-to-right with arrows facing toward you and pointing up) and ZH 3-pin's red-black-yellow (left to right; crimped connector openings facing toward you; wires coming out the bottom). Place heat shrink. Solder XH 4P to ZH 3P male: red with red, yellow with black, black with yellow.

  3. Solder ZH 3P female to XH 3P: red with red, yellow with black, black with yellow (I think; see troubleshooting below if it behaves weirdly like this)

  4. Unscrew the top beam of the gantry (on which the default filament holder rests). Run the part of the cable with the ZH female socket down the left extrusion of the gantry.

  5. Place the top beam back in place, while tucking the cable into cable management slits in said beam. Screw in once done.

  6. Turn printer around and unscrew bottom side. Plug motherboard side of cable into motherboard, connect opposite end with cable run through extrusion. Screw bottom side back in once done.

  7. Jump to step 9 of assembly instructions. See Troubleshooting Cable in case of incorrect function.

Troubleshooting Cable

When I start a print, the printer begins bootlooping / quickly power-cycling

This usually happens if your cable creates a short-circuit. You might need to flip the signal pin with power or ground.

Printer considers sensor signal inverted

Apparently some cheap sensors invert their signal pin. It might be possible to un-flip it through a solder bridge inside the sensor or flipping some of the wires.

Tagi