1 / 3
USS Drybox MMU3 Buffer Conversion for Core ONE — zdjęcie 1
1 / 3

USS Drybox MMU3 Buffer Conversion for Core ONE

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

MMU3 USS Drybox buffer conversion for Core ONE with 8x drybox routing setup.

Ocena
0 / 5
Polubienia
6
Pobrania
8
Wydruki
0
Wyświetlenia
355
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
GNU General Public License v2.0

Summary

This model aids in converting the MMU3 buffer to work with 8x USS Dryboxes mounted on the Core ONE. The primary issue with the stock MMU3 buffer is that it can only be loaded from one side. Additionally, the output exits from the same side, requiring the tubing to bend upward to reach the MMU3. Since the dryboxes are mounted on both sides of the machine, there needed to be a way to load the MMU3 buffer from either side while maintaining short filament paths.

Buffer Conversion

Reposition the buffer clips so the buffer stands on its long side. A second buffer faceplate from BUFFER - FOR ALL PRINTERS - R4/segmenter-R4 is added to the opposite side, allowing buffer wheels to be loaded from either side of the machine. Print the included adapter and install it in the center of the short top section of the buffer. Once assembled, place the buffer behind the CORE One.

MMU3 Tube Modifications

From the Prusa USS Drybox models, the PTFE Add-ons/PTFE-Stopper and PTFE Add-ons/PTFE-Connect are utilized to aid in loading filament through the buffer.

Insert short sections of PTFE tubing (~100 mm) into the MMU3 and install a PTFE-Connect on the opposite end of each tube (see images). Add longer PTFE tubes that extend down into the buffer and install the corresponding PTFE-Connect on one end.

Install a PTFE-Stopper on the opposite end of each longer tube. PTFE tube length depends on your setup; it should be long enough to gently arc toward the MMU3 and extend just past the included adapter clip, so the PTFE-Stopper sits just inside the buffer. This prevents the tube from falling out of the included adapter while keeping it properly positioned within the buffer.

Add additional tubing from the USS Drybox filament port to the bottom buffer wheel port. Install PTFE-Stoppers on the drybox-side ends of the tubing, following Prusa’s recommendation. The top buffer wheel port is not used. Each side uses two long tubes and two short tubes to match the drybox locations. Mount the dryboxes so the filament ports are centered vertically between upper and lower dryboxes to minimize path resistance and avoid sharp bends in the filament path.

Loading Filament

To load filament, remove the buffer wheel from the slot being loaded. Feed filament through the tubing from the drybox to the buffer wheel and set it aside.

Disconnect the PTFE-Connect on the MMU3-side tubing that leads into the top of the buffer. Push the tubing down into the buffer and out through the faceplate on the side being loaded (see image). The PTFE-Connect prevents the tubing from slipping out during this step.

Take the filament exiting the buffer and push it through the tubing until it extends slightly past the top of the PTFE-Connect. While holding the filament in place, pull the tubing back into its normal position within the buffer.

Feed the filament into the MMU3, then reconnect the PTFE-Connect fittings and press the tubing into the included PTFE clip adapters on top of the MMU3 to lock it in place.

The buffer wheel should be loaded so filament enters through the bottom port and naturally bends upward toward the MMU3. This uses the wheel to reduce friction. Avoid using the top port, as it introduces significantly more resistance.

Resources

  • The USS Drybox mounts for the Core ONE can be found here:

  • I found that it was absolutely necessary to center filament rolls within the drybox. I found these spacer sleeves very useful to fit various inner spool diameters without needing a full cylinder spacer:


Tagi