1 / 7
Velux KIG 300 (NXG01E) 10-Inch Rack Mount (1U) — zdjęcie 1
1 / 7

Velux KIG 300 (NXG01E) 10-Inch Rack Mount (1U)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

1U 10-inch rack mount for Velux KIG300 / NXG01E. Uses original white mounting stub.

Ocena
0 / 5
Polubienia
1
Pobrania
5
Wydruki
0
Wyświetlenia
42
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Share Alike

Velux KIG 300 (NXG01E) Active Gateway 10-Inch Rack Mount (1U)

Clean up your smart home setup and mount your Velux KIG 300 / NXG01E Active Gateway (Netatmo Velux Gateway) directly into your 10-inch SOHO network rack!

This sleek 1U faceplate features an integrated mounting arm designed to utilize your gateway's original white wall-mount clip (stub). By screwing the OEM clip onto the 3D-printed bracket, you get a perfect, manufacturer-grade snap-fit that holds your gateway securely flush with your rack.

Key Design Features
  • Flush Front Fillets: The front cutout is designed with elegant internal fillets. The gateway is inserted from the back, allowing it to seat perfectly flat and flush against the front face for a highly professional, integrated look.

  • Front-Facing Status & Power: The gateway is intentionally oriented with its 2-pin power port (figure-8 / IEC C7 style) and status LED facing forward. This allows you to monitor your smart home connection status at a glance without looking behind the rack.

  • Integrated Power Cable Pass-Through: A clean, built-in pass-through slot on the left side of the faceplate allows you to route the power cable neatly from the back of the rack directly to the front-facing port.

  • OEM Snap-Fit: Uses the original white mounting clip from your Velux retail package for a secure, wear-resistant lock.

  • Honeycomb Support Bracket: The perpendicular support arm features a stylish hexagonal cutout pattern designed to prevent a bulky, unattractive block of solid plastic while maximizing structural stiffness and rigidity.

  • Zero-Support Print: The provided .3mf file is pre-oriented face-down. This allows you to print the faceplate directly on your build plate (ideally textured PEI) for a premium front-panel finish with zero supports required.

📦 Bill of Materials (BOM)

3D Printed Parts
  • VeluxKig300RackMount_1U_1x.3mf - Slicer-ready file, pre-oriented face-down.

Hardware & OEM Components
  • 1x M3 Threaded Heat-Set Insert (Standard Voron size: M3 x 4.6mm x 4.0mm)

  • 1x M3 x 8mm Socket Head Cap Screw (SHCS) or Button Head Cap Screw (BHCS)

  • 1x Original white wall-mounting clip (included in the Velux KIG 300 box)

🔧 Assembly Instructions

  1. Install the Heat-Set Insert: Using a soldering iron set to the recommended melting temperature for your chosen printing filament, gently press the M3 heat-set insert into the designated hole at the end of the honeycomb mounting arm until it is completely flush.

  2. Mount the OEM Clip: Position your original white Velux wall-mount clip over the end of the honeycomb arm, ensuring its physical alignment tabs drop securely into the corresponding recesses on the printed plastic bracket.

  3. Secure the Clip: Thread your M3 x 8mm screw through the center of the white clip and tighten it directly into the newly installed heat-set insert.

  4. Click-In the Gateway: From the back of the faceplate, insert your Velux KIG 300 Gateway into the rectangular cutout and slide it forward until it rests flat against the internal front fillets. Snap it firmly onto the white mounting stub (ensuring the power port and status LED face forward through the cutout).

  5. Route Power: Run the power cable through the integrated pass-through slot on the left and plug it directly into the front port of the gateway.

If you find this mount useful in your homelab, please consider uploading a photo of your make!

Tagi