1 / 8
AMS Lite Launcher & Filament Roll Battle Top with Flywheel/Clutch — zdjęcie 1
1 / 8

AMS Lite Launcher & Filament Roll Battle Top with Flywheel/Clutch

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Sleeper Battle Top | Integrated Flywheel clutch | AMS Lite launcher with Stand

Ocena
0 / 5
Polubienia
6
Pobrania
10
Wydruki
0
Wyświetlenia
118
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

AMS Lite Launch and Filament Roll Battle Top

This sleeper battle top looks like a simple roll of filament, but has a hidden secret. The spooled filament is actually an all-plastic fly wheel that keeps the top upright and spinning after impact. Using a one-way bearing the fly wheel is up to speed on launch, but can continue to spin when the top is slowed from impact. 

Update 07/02/26

Published major revisions for improved spin and stability. Now spins for over 3 minutes!

  • Reduced gear pitch diameter from 22.5mm to 8mm

  • Increased ripcord teeth coverage from 173mm to 222mm

  • Spins about 3x as much on a single pull (I think)

  • Added a much sharper tip on the bottom without changing the height of the blade

  • Balanced the blade by partially filling the holes to even out the weight opposite the decorative elements that have no holes

  • Reduced the height of the teeth so that the top looks even more like a roll of filament

Features

  • Meets competition specs from stlDenise top

    • 272.6mm ripcord

    • 90mm blade diameter

    • blade 25mm high

  • All-plastic Flywheel/Clutch

    • 100% infill flywheel overruns the spool body after impacts providing gyro forces to keep the top upright

    • One way bearing acts as a clutch, dampening the impacts and allowing the top to keep spinning, using friction from the flywheel to gradually bring the top back up to speed

    • One-way bearing locks on launch so the flywheel is accelerated with the top, without sapping the tops rotation like freewheel designs.  

    • Uses the same one-way bearing concept as my dice tower

  • All-plastic design

Print Settings

  • Filament: PLA with 2 Colors (White, and Black)

  • Nozzle 0.4mm

  • Layer Height: 0.16mm

  • Infill:

    • 100% Concentric: blade, flywheel, and spacer

    • 15% Gyroid: everything else

  • Walls: 2

  • Supports: None

Assembly

  1. Spool Holder Top: Place onto build surface, with X face up

  2. Spool Top: Place onto Holder Top, with text face down

  3. Spacer: Place onto the spool, lip face up

  4. Flywheel: Place the flywheel on the spacer, opening down, so it surrounds the space

  5. Spool Bottom: Place the spool bottom on the flywheel, flat side down

  6. Spool Holder Bottom: Line up the holes of the bottom with the holes in the X, and place onto the X

  7. Pin: Secure the end with a cut of filament

  8. Trim filament to fit (Not pictured)

  9. Teeth: Flip over and screw in the teeth to the spool holder

  10. Stand: Remove the modeled-in supports from the AMS Stand. You can remove by hand with some twisting, or with a tool for a better finish

  11. Finish: You are ready to battle!

Usage Instructions

  1. Set the top inside the opening on the launcher, teeth up

  2. Insert the ripcord from the right (may need to wiggled the top to get the teeth to mesh) 

  3. Hold the AMS Lite, with your hands clear of the blade

  4. Pull the ripcord!

Note: Flexing the ripcord away from you gets the best results with no gear slipping

Tagi