1 / 14
Pop-Up Toaster — Toy with a REAL Spring-Launched Pop — zdjęcie 1
1 / 14

Pop-Up Toaster — Toy with a REAL Spring-Launched Pop

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A pretend-play toaster that actually works: press the side lever DOWN and it clicks down and latches

Ocena
0 / 5
Polubienia
1
Pobrania
8
Wydruki
0
Wyświetlenia
126
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

A pretend-play toaster that actually pops. It is not a static prop — it has the real mechanism inside.

Printed pop-up toaster — toast popped up

How you play

  1. Press the side lever knob DOWN, firmly, all the way to the stop. The toast carriage sinks, compressing the printed coil springs, and CLICKS into the latch — it stays down, just like loading a real toaster.

  2. Push the side EJECT buttons — POP! — both toast slices spring up and jump out of the slots.

How it works (the real bit)

  • Five printed helical coil springs sit under the carriage and store the pop energy. They're separate, replaceable parts — print them in PETG so they don't take a set while the toaster sits loaded.

  • A self-engaging sear latch on each side wall catches the carriage at the bottom of travel. Pressing down cams the latch aside and over-travels so it snaps under and holds — the same trick a 1950s toaster uses.

  • The eject buttons move only the light latch (a couple of newtons), while the springs supply the launch. That force-decoupling is why a gentle push releases a strong pop.

  • Snap-together, no glue: the base clicks into the shell, the ejectors snap into their wall slots, and the knob is a slotted snap-rivet.

Loaded / latched (pressed down — stays loaded):

Loaded and latched, pressed down

Popped (buttons pushed — springs release):

Popped, toast launched

The parts (10 printed pieces)

Exploded view of all parts
  • toaster_shell ×1, toaster_base ×1, toaster_carriage ×1, toaster_knob ×1 — PLA

  • toaster_spring ×5 — PETG (PLA creeps → dead pop)

  • toaster_ejector ×1 + toaster_ejector_left ×1 — PETG

  • toast: toaster_toast ×2 (single colour) or the AMS pair toaster_toast_bread + toaster_toast_crust ×2 (two-colour)


Assembly — one picture per step

Colours below match the renders: red = shell, grey = base, gold = carriage, pale-blue = springs, silver = ejector, brown = toast. Work with the shell upside-down (toast slots on the bench) and build into the open bottom. No glue anywhere.

Step 1 — Ejectors into both walls (PETG). From inside the cavity, push each ejector's button out through its wall slot until the barb clicks over the top edge; the long leaf drops between the two inner posts. Do both walls.

Step 1 — ejector seated, button poking out

Step 2 — Five springs onto the base. Stand one coil over each guide rod — four corners plus one centre. They just sit on; the rods stop them bowing.

Step 2 — five springs on the base guide rods

Step 3 — Carriage onto the springs. Toast platforms up, the two latch stubs to the side walls. The spring top pads tuck into the carriage seats.

Step 3 — carriage set on the springs

Step 4 — Drop the stack into the shell. Lower the carriage in (guide ribs into the edge notches, platforms up into the slot chimneys), then press the base up until its 4 snap-fingers click into the wall windows. Now it's captive — picks up as one piece.

Step 4 — stack dropped in, base snapped (cutaway)

Step 5 — Knob on the outside. Push the knob's slotted snap-rivet pin through the lever groove into the stub bore until it clicks. Hand-press, no glue.

Step 5 — knob pressed onto the lever stub

Step 6 — Toast in. Done. Drop the two slices into the slots. Press down to load, push the buttons to pop.

Step 6 — toast in, finished toaster

Printed & assembled

Assembled toaster, side

All printed parts laid out

Safety: launch energy is ~7 mJ per slice — about 11× under the CPSC toy projectile limit. The toast slices are larger than the small-parts choke gauge. No sharp edges. Print springs + ejectors in PETG; supervise small children with any spring toy. The .scad source is attached so you can re-tune it.

Tagi