Subnautica 2 portable locker

Summary

This is a recreation of the portable locker from Subnautica 2. I made this with my partner @AaronHan_5020623 and the steps to make this design are down below on this page.

Assembly/Construction

Base

1. Open a sketch and click on the front plane to make a 20 by 20 constraint box and make the box on construction

   2. Make a trapezoid with lines and use a angle smart dimension of 111 cm and two smart dimensions of 15 cm and 6 cm 

1.  Extrude the base by 10 cm 

1. Make a semicircle with a radius of 2 cm and two smart dimensions of 6 cm and 2 cm

1. Extrude the bottom by 15 cm on the mid plane 

1. Use the fillet tool to fillet the top, sides and bottom of the base box by 1 cm 

      7. Open a new sketch to make a circle on the top plane 

1. Extrude the circle by 0.25 cm 

1. Fillet the circle by 0.10 cm 

1. Open a new sketch to make another circle on top of the big circle

1. Extrude the circle by 0.25 cm

1. Fillet the circle by 0.10 cm

Handles

1. Open a new sketch and make a circle and have a smart dimension of 0.81 cm

1. Make a sketch on the top plane and make a lines with horizontal, vertical and tangent relations that connects to the circle 

1.  Use those sketches to make a sweep 

1. Open a new sketch and make more lines and curved lines and use the mirror tool to mirror the lines and the bodies 

1. Make a new plane coincident on the surface and make a new sketch to make a square with a smart dimension of 4.70 cm 

1.  Extrude the square by 0.3 cm 

7. Fillet the square by 0.5 cm 

8. Use the chamfer tool to chamfer the square by 0.5 cm and 45 degrees 

9.  Make another sketch and create a stadium on top of the square and use smart dimension to add a measurement of 0.36 cm and 5.19 cm 

1. Use extrude cut to cut extrude for 0.15 cm

1. Mirror the square to the other side of the base box

Ridge

1. Make a new sketch and make a circle that slightly intersects the base box 

1. Open another new sketch and make a path with lines 

3. Make a sweep using the two sketches you made

4. Make a plane on the sweep

5. Use the plane to mirror the entire sweep

6. Make a mid plane and mirror the sweep so it is on both sides

1. Fillet the ridge and handle by 0.01 cm 

Bottom

1. Make a new sketch on the bottom of the base box and add a smart dimensions of 0.7 cm, 0.5 cm and 0.36 cm

2. Extrude cut it by 0.15 cm 

1. Use linear sketch pattern to make 6 copies separated between 2.25 cm

1. Fillet it by 0.01 cm 

Splitting bodies and moving it 

1.  Make a line below the top of the base box to split the bodies 

1. Use move/body copy to move the lid up 

3. Make lines to cut extrude the inside of the box by 6 cm 

1. Cut extrude the lid by 0.75 cm and 18 degrees 

1. Make a sweep on the front plane of the base box

1. Fillet the sweep 

1.  Make the other part to make a latch

     8.  Using the split tool separate the handles from the base box, add circles on all four of them and boss extrude by 0.20 cm

1.  Use move/body copy to move the lid behind the base box, then cut extrude where the handles were by 0.20 cm

Hinges

1. Make a plane to make a sweep 

1.  Mirror the sweep

1.  Make a new sketch and make a circle on the sweep and box extrude it by 0.50 cm and 11 degrees, then mirror the box extrude 

1. Fillet it by 0.15 cm 

1. Hide the base box and make the same hinges on the lid 

1.  Use move/body copy to move the lid as close to the hinges as possible until they are side by side and extrude cut by 0.45 cm and 11 degrees 

Design Changes 

At first we were thinking of making the the circles at the top as a button that opens the box with stabilizer springs, but  we decided to just make a basic hinge and latch since it would be too complicated for us.