1 / 6
Midea PortaSplit 150mm exhaust hose attachment / Luftschlauch Aufsatz — zdjęcie 1
1 / 6

Midea PortaSplit 150mm exhaust hose attachment / Luftschlauch Aufsatz

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Easy removeable and attachable exhaust hose attachment for the Midea Portasplit, with extra air regulation

Ocena
0 / 5
Polubienia
10
Pobrania
100
Wydruki
0
Wyświetlenia
758
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

English:

An attachment for the Midea PortaSplit to distribute cold air into multiple rooms using a 150mm exhaust hose.

Thanks to the two openings with an adjustable flap, you can easily vary how much air flows out directly, allowing you to cool either just one room or two rooms.

The design can simply be placed on top of the PortaSplit and secured using the 2 clips on the side handle openings.

Requirements

  • Filament: Approx. 1kg (budget PLA is sufficient; I used the affordable TheFilament PLA Lite)

  • Build Volume: At least 200x215x200mm

Hardware:

  • 16x M3 nuts

  • 2x M3x16 screws - for the adjustable air flap

  • 10x M3x12 screws - to connect the split housing

  • 4x M3x10 screws - to connect the hose to the housing

Note: These are the minimum screw lengths, but slightly longer screws will work as well.

Printing

  • All required files are pre-configured in the .3mf file.

  • The 3 split "Main" parts are equipped with round helper discs (mouse ears) to prevent the parts from warping during printing. These can be easily removed afterward.

  • Enable automatic supports, but manually disable supports inside the screw holes (this is already done in the .3mf file).

Assembly

  1. Connect the three "Main" parts together using the M3x12 screws and nuts.

  2. Attach the two "Flap" parts to the inside and the "FlapGrip" parts to the outside, then secure them with the M3x16 screws and nuts. Ideally, use locknuts (nyloc nuts).

  3. Connect the "TubeConnector" to the housing using the M3x10 screws.

  4. Attach the 150mm hose to the "TubeConnector" using a hose clamp.

  5. Secure the housing to the Midea unit using the 2 "Clip" parts.

Deutsch:

Ein Aufsatz für die Midea PortaSplit um die Kalte Luft mit einem 150mm Abluftschlauch in mehreren Räumen zu verteilen.

Dank der zwei Öffnungen mit drehbarer Klappe, kann man sehr einfach variieren wie viel Luft direkt raus strömen soll um entweder nur einen Raum, oder zwei Räume zu kühlen.  

Die Konstruktion lässt sich einfach auf die PortSplit drauf legen und mit den 2 Clips an der seitlichen Grifföffnung fest machen. 

Anforderungen:

  •  Filament: ca. 1kg (günstiges PLA reicht aus, ich habe das günstige TheFilament PLA Lite verwendet)

  • Bauraum: Mindestens 200x215x200mm

Hardware:

  • 16x M3 Muttern

  • 2x M3x16 Schraube - für die drehbare Luftklappe

  • 10x M3x12 Schraube - um das aufgeteilte Gehäuse zu verbinden

  • 4x M3x10 Schraube - um den Schlauch mit dem Gehäuse zu verbinden

Hinweis: Das sind die Mindestlängen der Schrauben, etwas längere Schrauben funktionieren aber auch.

Druck:

  • In der .3mf Datei sind alle Dateien vorbereitet die benötigt werden. 

  • Die 3 aufgeteilten "Main" Teile sind mit runden "mouse ears bestückt damit die Teile während dem Druck nicht warpen, diese können sehr einfach nach dem drucken entfernt werden. 

  • Automatische Stützen aktivieren, aber manuell Stützen in den Bohrungen deaktivieren (in der .3mf Datei schon erledigt)

Zusammenbau:

  1. Die drei "Main" Teile mit den M3x12 Schrauben und Muttern zusammen verbinden

  2. Die zwei "Flap" in der Innenseite anbringen und von Außen die "FlapGrip" anbringen, dann mit den M3x16 Schrauben und Muttern befestigen. Idealerweise Sicherungsmuttern verwenden. 

  3. Den "TubeConnector" mit den M3x10 Schrauben mit dem Gehäuse verbinden.

  4. Den 150mm Schlauch mit einer Schlauchschelle mit dem "TubeConnector" verbinden

  5. Das Gehäuse mit den 2 "Clip" an die Midea befestigen

Tagi