Dusch Hörer für 1/2" Zoll Gewinde mit Wandhalterung.
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Duschgriff in Telefon Hörer Form für 1/2" Zoll Gewinde mit Wandhalterung.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 9
- Wydruki
- 0
- Wyświetlenia
- 60
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Bathroom
- Licencja
- Creative Commons — Attribution
Duschgriff in Telefon Hörer Form. 2 Teile. (Griff und Gewinde) Hier für 1/2" Zoll Gewinde. Der Duschgriff V2 hat innen einen größeren Querschnitt bis zu den 4.1/2mm Ausgängen.
Erforderliche Bauteile:
● PTFE Schlauch mit 4.1mm Außendurchmesser.
● Zweikomponentenkleber (UHU Plus Endfest) für die konischen Flächen.
Erforderliche Werkzeuge:
● Scharfes Messer zum präzisen und Rechtwinkligen Schneiden des PTFE Schlauches in ca. 7mm lange Stücke.
● 4.1mm Spiralbohrer zum passgenauen Ausbohren der 4mm Löcher.
● Handschrauber für den 4.1mm Spiralbohrer.
Verwendetes Filament:
● PETG. (Jayo weiß)
Slicer Empfehlungen:
● Die Stützstrukturen nur außerhalb des Duschgriffs Generieren.
● 4 Wandperimeter (2mm) empfohlen.
● Duschgriff Druckgeschwindigkeit von ca. 40mm/s. empfohlen.
● Gewinde Druckgeschwindigkeit von ca. 20mm/s. oder weniger empfohlen.
Zusammenbau:
● Die Bauteile von der Druckplatte nehmen und die Stützstrukturen entfernen.
● Zuerst das Bauteil mit dem 1/2" Zoll Außengewinde in den Schlauch mit dem 1/2" Zoll Innengewinde Schrauben und prüfen ob beides gut passt.
● Die 4mm Löcher mit dem 4.1mm Spiralbohrer aufbohren und die Filament Reste entfernen.
● In alle 4.1mm Löcher ca. 7mm lange PTFE Schlauch Stücke fest Einstecken.
● Zweikomponentenkleber auf die konische Innenfläche des Duschgriffs (unten) und der konischen Außenfläche des Gewindes (oben) auftragen.
● Die beiden Bauteile mit den konischen Flächen fest zusammen stecken und fest an drücken.
● Die geklebten Bauteile für 12 Stunden aushärten lassen.
Wasserstrahl Einrichtung des fertigen Duschgriffs:
● Eine 2mm dicke Fahrrad Speiche (oder ähnliches) nehmen und die einzelnen PTFE Schlauch Stückchen nach bedarf ausrichten damit alle Wasserstrahlen parallel verlaufen.
English:
Shower handle in the shape of a telephone receiver. 2 parts. (Handle and thread) Here for a 1/2" inch thread. The shower handle V2 has a larger internal cross-section up to the 4.1/2mm outlets.
Required components:
● PTFE tubing with 4.1mm outer diameter.
● Two-component adhesive (UHU Plus Endfest) for the conical surfaces.
Required tools:
● Sharp knife for precise and right-angled cutting of the PTFE tubing into approx. 7mm long pieces.
● 4.1mm twist drill bit for precise drilling of the 4mm holes.
● Hand screwdriver for the 4.1mm twist drill bit.
Filament used:
● PETG. (Jayo white)
Slicer recommendations:
● Generate support structures only outside of the shower handle.
● 4 wall perimeters (2mm) recommended.
● Shower handle printing speed of approx. 40mm/s recommended.
● Thread printing speed of approx. 20mm/s or less recommended.
Assembly:
● Remove the components from the build plate and remove the support structures.
● First, screw the component with the 1/2" male thread into the hose with the 1/2" female thread and check if both fit well.
● Drill out the 4mm holes using the 4.1mm twist drill bit and remove any remaining filament.
● Firmly insert approx. 7mm long pieces of PTFE tubing into all 4.1mm holes.
● Apply two-component adhesive to the conical inner surface of the shower handle (bottom) and the conical outer surface of the thread (top).
● Firmly push the two components with the conical surfaces together and press them tight.
● Allow the glued components to cure for 12 hours.
Water jet alignment of the finished shower handle:
● Take a 2mm thick bicycle spoke (or similar) and align the individual PTFE tubing pieces as needed so that all water jets run parallel.