Twin Check Sticker Dispenser / Peeler for film development
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,69 € – 0,84 € netto (bez VAT)
Dla pliku: TwinCheck_Spool_Guide_Peeler_0.4n_0.25mm_PLA_COREONE_36m.bgcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,76 € netto (środek widełek).
- Masa podana przez autora
- 13 g
- Czas druku podany przez autora
- 36 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Roll holder with peel edge for dispensing film lab twin check labels cleanly, one pair of stickers at a time.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 26
- Wydruki
- 0
- Wyświetlenia
- 136
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Photo & Video
- Licencja
- Open Community License v1.1 + General Attribution v1
I couldn't find any existing models so made this dispenser to peel and hold Noritsu / Fuji style twin check stickers.
I actually use these to keep track of my film from shooting, through development to archive.
 |  |
The roll sits on the holder and feeds the labels over a peel edge, helping separate each sticker from the backing paper cleanly. It keeps the roll controlled on the bench and makes it easier to dispense one label at a time without the strip curling, tangling, or sticking to itself.
Designed for straightforward 3D printing and practical use in a small lab, home darkroom, or film-processing setup.
Designed to:
deposit labels one pair at a time on a ledge to use
prevent unwinding when not being used with light friction
need minimal force to dispense labels
be easily printed without any supports or tuning where possible
keep the guide roller captive but loose
spool easily removable
Print Settings
My print settings (has quite a solid stable weight):
Prusament PLA
3 perimeter walls (just out of habit)
0.6mm nozzle (0.4 will give a better finish but be slower)
0.4mm Structural preset with variable layer height
20% infill
3mm inner and outer brim for insurance (maybe not necessary with PLA but its a long thin tall piece)
The body should be placed vertically on the print bed, that way no supports are needed
The peeler should have the flat surface on the print bed so no supports are needed
The guide and spool should be placed vertically with supports generated, so they spin freely
Assembly
 | (1) The smaller spool slots in the guides and remains loose |
 | (2) The larger guide goes in the front slot, it needs to be pushed past the wedge until it clicks into place |
 | (3) The peeler is wedged between the wide of the body. It should be a tight fit but if its loose you can glue it on the flat edge. |
 | Thread the labels through this path to dispense. |
This sort of worked perfectly the first time I printed it with no second version, so if you have any suggestions let me know, I have not iterated on this.
If you want to sell this message me.