Updated MarcoZ76's Bondtech BMG Prusa MK3S/MK2.5S for two hole fan shroud
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
tightened square nut holes , modified clamping , added nozzle fan mount, fixed a few printing things
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 6
- Wydruki
- 0
- Wyświetlenia
- 61
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- GNU General Public License v2.0
Loved MarcoZ76 BMG extruder and a big thanks to him for this excellent model , I just found a few little things that bugged me , one major one being where the clamping force was being applied to a very thin section around the extruder mount with two drop in square nuts , as i was playing around with making an adaptor for a Phaetus dragon and printed a extruder adapter that was a little too big like we are talking .02 of a millimetre this added a little clamping force to it around the extruder collet at the top , but as i tightened it up on a polycarbonate carbon fiber print i heard a distinct cracking noise ... opps that's not so good a weak Z being pulled instead of compressed, so went back and looked at the model size for the Phaetus Dragon adaptor I found that it really was not that far off spec, so i looked at the model of the BMG extruder front where the bolts tighten and yea they were in a very thin section of the model so not much there for any clamping force , so I loaded up the model and started changing how it clamps down by moving the nuts to better tolerate stress around the extruder top collet so i can get that clamping force holding the extruder body tight without cracking the extruder body .
I also thought the bridging fan shroud needed an additional fixing point so added that as well .
Also modified the fan shroud with the additional bolt mount .
Cleaned up a few holes , some little changes to bevel a few edges .
Tightened up the square nut holes as i was getting tired of picking my nuts up off the floor , trying to find them as they bounce off to the square nut land and i only have about 50 of them left .
for reference my square nuts are 1.7mm thick 5.43x5.43 the cutouts are 5.6x5.6 x 2.0 thick , seems tight but really not too tight they slide in and stay there till i want to take them out, your printing tolerances may vary so let me know if its too hard to push the nuts in .
Added mounting at the top for accessories , such as accelerometer or as i want to screw on a bracket for water cooling loop to come down from the top of my enclosure seemed like a good time to add a couple of extra fixing points , just be careful to not put m3 bolt in them that is too long as there's no counter hole on the other half of the extruder body and you will push the two halves apart , well until i might mod that as well as still a couple of things I might want to do to that .
I will add my hose holding water cooling bracket for the top mounts once that is finalized , and throw in a few more pictures as i build .
Can find the dual mount hole fan shroud here :
https://www.printables.com/model/1784268-dual-hole-mount-fan-shroud-for-marcoz76-v2-bondtec
Also another version I made in Delta-P style :
https://www.printables.com/model/1801356-bmg-bondtech-delta-p-duct-with-led-mounts
For all the details see MarcoZ76 publication as he has a lot of details there about x-carriage compatibility and everything else .. and let me know if you have something you would like to add , there is also an assembly guide on the bondtech website that is very helpful and side note you need to install the bondtech firmware for XYZ calibration to work as there is a little difference in the Z height.
enjoy.
feel free to use , let me hear your thoughts if you like the redesign .. does the redesign of the clamping help you ? do your nuts fit in ?
