1 / 9
Polar Cross-Ply Infill — Radial/Hoop Toolpath Demo Rotor — zdjęcie 1
1 / 9

Polar Cross-Ply Infill — Radial/Hoop Toolpath Demo Rotor

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Demo part using polar cross-ply infill: alternating radial + hoop toolpaths for stronger axisymmetric FDM parts.

Ocena
0 / 5
Polubienia
1
Pobrania
9
Wydruki
0
Wyświetlenia
72
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Engineering
Licencja
Creative Commons — Attribution

⚠ Read first: this is G-code, not an STL

Update — v3.1 (July 2026). Replace any earlier download.

The previous file was 14% under-packed and printed with visible grooves between every road. The cause was setting road width equal to road pitch. Adjacent extrusions are rounded, not rectangular, so they must be spaced at w − h(1 − π/4) — the width a bead occupies once its shoulders nest, not its widest dimension. Every dimensional error in this project traced back to that one relation.

Six print iterations, measured with calipers each time:

deposition

height error

original

0.86 (under)

grooved, gappy

first "fix"

1.152

+8.8%, domed, OD grew with Z

corrected width

1.021

+2.0%

snapped pitch

1.005

−0.3%

Final part measures OD 66.06–66.22 against 66.20 nominal.

This file is a test article, not a pretty part. It has no perimeters and a single top/bottom layer, deliberately — the open rim exposes the layer cross-section so the toolpath can be measured directly. It will look rough. That's the point. A walled presentation version is coming once the wall-to-infill spacing is verified.

Full method, measurements, and the five approaches that failed (four spiral variants and a helical wall, each with the reason): https://github.com/HankLarsen/Polar-Crossply-Infill

Final part measures OD 66.06–66.22 against 66.20 nominal.

This upload is pre-generated G-code for a specific toolpath pattern that stock slicers can't produce. You don't slice it yourself — you print the file directly, or generate your own size with the free tool on GitHub (link below). Sliced for a 0.6 mm nozzle, 1.0 mm extrusion width, 0.4 mm layers. Set your own temperatures and paste your printer's start/end G-code before printing — the built-in defaults are generic and may not suit your machine.

What is polar cross-ply infill?

It's cross-ply plywood, but in polar coordinates. The part is filled with toolpaths aligned to the two natural directions of a round part, and the direction alternates every layer:

  • Hoop layers — concentric rings (roads run around the part)

  • Radial layers — spokes from the bore outward, added in bands so the spacing stays even instead of fanning out

Stacking the two gives you continuous, load-following roads through the whole thickness in both in-plane directions of a disc — radial and hoop — instead of the generic 45° grid a normal slice lays down.

What's it good for?

Round, axisymmetric parts loaded by spinning, press-fit at the center bore, or radial/hoop pressure: discs, rings, washers, flywheel and pulley blanks, hubs, bearing carriers. The hoop layers reinforce the bore (where those parts fail first); the radial layers tie the center to the rim.

When NOT to use it

This is a special-purpose pattern, not a general infill. It's meaningless on non-round parts, and it's weakest in torsion (twisting the hub against the rim), so it's a poor choice for a driven gear or pulley unless you add a metal hub. Full honesty on strengths and weaknesses is in the docs.

The demo part

A ~66 mm rotor with a 10.5 mm bore, printed essentially solid — so the pattern is about fiber direction, not saving weight. The photos show a radial layer mid-print (the sunburst) next to the concentric layers it alternates with.

Make your own / read the details / contribute

Everything is open source (MIT): a standalone G-code generator for any disc/ring size, a reference implementation of the pattern, full documentation, and an honest writeup of the mechanics and prior art.

👉 GitHub

Note: this model was created with AI assistance for the code and documentation. The pattern, the engineering, and the printing are my own.

Tagi