portable 130mm(F4) and 150mm(F5) Newtonian telescope
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a foldable 130mm and 150mm portable reflecting telescope.
- Ocena
- 0 / 5
- Polubienia
- 15
- Pobrania
- 43
- Wydruki
- 1
- Wyświetlenia
- 322
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Physics & Astronomy
- Licencja
- Creative Commons — Attribution — Share Alike
The weather has been continuously cloudy lately, so I haven't been able to go outdoors... While sitting at my desk, I put together and posted the assembly instructions for a design I created earlier.
So far, I’ve completed testing for visual observation. I was planning to do imaging tests, but the DIY mount I built was acting up. Acquiring a commercial one took a bit of time. The mount arrived about a week ago... but now the weather isn't helping at all. 😭
When I tested the 130P in Mongolia, using a 7mm eyepiece partially resolved the stars at the outer edge of the M13 globular cluster. I'll take my time with the imaging tests once the skies clear up.
The attached drawings are for both the 130P (F4) and 150P (F5). You can pick and build whichever one fits your needs.
The focuser used here was built using an open-source 2-inch focuser design. You can assemble and mount the focuser from the link below:
https://marcosatm.com/2020/06/04/2in-crayford-focuser/
Please refer to the attached assembly guide file for step-by-step instructions.
# Key Features
Foldable & Collapsible for easy storage
Fits inside a backpack when folded (130P fits comfortably, 150P barely fits — based on a 19-inch travel backpack)
Carry-on luggage compatible for flights! (The absolute biggest advantage!)
Supports a 2-inch focuser
Relatively lightweight (~2.5 to 3.0 kg)
Includes tube rings: Makes visual observation on an equatorial mount much easier. The center of gravity can also be adjusted by moving the ring position.
# Assembly Instructions
I’ve uploaded the design files as attached zip archives (130P.zip and 150P.zip). You can download and print them with a 3D printer.
# BOM (Bill of Materials)
Primary Mirror: Prices vary depending on precision. A 1/6 lambda optical quality mirror costs around $110 USD (~150,000 KRW) on AliExpress.
Note: You must select a parabolic mirror. Don't be tempted by cheap spherical mirrors, or you'll regret it! 😄
Other Components: No other expensive parts are required.
Hardware: You'll need quite a few bolts, nuts, countersunk (CSK) screws, and heat-set inserts.
M6 insert x 4:
M5*40mm knob bolt x 3:
M5*30mm x 1:
M5*20mm knob bolt x 2:
M5*15mm knob bolt x 3:
M5*12mm x 3:
M5 insert x 17:
M4 insert x 11:
M4 nut x 9:
M4*30mm knob bolt x 3:
M4*30mm x 4:
M3 nut x 3:
CSK M4*22mm x 3:
CSK M4*18mm x 3:
CSK M4*16mm x 6:
CSK M3*4mm x 3:
Yellow mold spring 10*25 x 4:
Carbon pipe (outer diameter 12, inner diameter 10) x 3: 130P(Length 294mm), 150P(Length 405mm)
primary mirror x 1: 130P=D133F520(F4), 150P=D150F750(F5)
Adhesive nonwoven fabric (1T) x 2: 130P(25*580mm), 150P(25*623mm)
silicone adhesive x 1:
secondary mirror x 1: 130P=40mm, 150P=50mm
Neodymium circular magnet 6*3mm x 6:
5mm steel ball x 3:
