Low D Whistle — Pin-Hinge Key with Rubber Band Return
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A extender key for the bottom note of a Low D tin whistle
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 45
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Music
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
# Low D Whistle -- Pin-Hinge Key with Rubber Band Return (proof of concept)
A replacement key mechanism for a printed Low D tinwhistle, built after a
single-piece flexure key kept fatiguing and cracking in PETG. This design
splits the job into three separate, independently working parts instead
of asking one thin plastic section to be both a pivot and a spring.
## Status: proof of concept, not a finished/polished part
This works -- the hinge rotates freely, the band returns the key to a
consistent rest position, and the pad seals the tone hole well enough to
prove the mechanism functions. It is NOT presented as a final, ready-to-copy
design:
- The pad seal currently is from an adhesive foam pad, stuck onto the pad that covers the note holes. This new improved seal is combined with a slightly bigger pad size. The note hole covered successfully and did not produce a muffled sound any more.
- Hardware substitutions were used during testing (zip ties in place ofM3 bolts on the clamp rings, since M3 hardware wasn't on hand yet). Update on hardware, I tried M3-0.5 x 16 mm Wing Butterfly Screws and nuts, the screw was not long enough, I am guessing something like a 25mm screw would be needed, but I cannot find these, therefore small zip ties are the preferred solution for now.
## How it works
- Ring: clamps around the whistle body, split with a bolt closure
(same design as the earlier whistle/dizi builds in this series).
- Pin hinge: interleaved knuckle lobes (like a door hinge) with a
through-bore for a metal pin. Pure rotation -- no plastic bending, so
no fatigue at the pivot itself. Currently pinned with a nail cut in
half, 2mm diameter and 15mm long, snug in the bore; a snug (not
loose) fit was
found to add enough friction to resist over-swinging on its own, so
no separate mechanical stop is needed.
- Rubber band spring: an elastic band strung between a peg on the
pad's outer face and a peg on a second, separate anchor ring further
along the tube. Pressing the key stretches the band; releasing lets
it pull the key back open. A stretched rubber band is built for
thousands of repeat cycles in a way a thin printed wall isn't -- an
earlier printed flex-tab spring kept snapping, either from its own
fatigue or from the force needed to free a fresh knuckle joint
routing straight through it.
- Anchor ring: a second small ring, using the same clamp design as
the main ring, that can be slid to any position along the tube and
rotated to any angle before tightening. There's no single "correct"
position calculated in advance -- testing found that as long as
there's some pull-back tension in the band, the exact position isn't
critical.
- Pad: A adhesive backed foam pad stuck to the face of the key pad
sealing the tone hole when pressed.
## What you'll need to build one
The printed parts (ring, key/hinge assembly, anchor ring)
A nail cut in half, 2mm diameter and 15mm long, for the pin (or
similar small rod/wire -- just needs to fit the bore snugly)
M3 bolts + nuts for both clamp rings (zip ties work as a temporary
substitute)
A small elastic band or cut loop of elastic cord
Adhesive foam pad, cut to to size.
## Design history (why it looks the way it does)
This went through several complete redesigns in one evening:
1. A single-piece flexure key (living hinge) -- worked in concept but
kept cracking in PETG at the thin flex zone, even after ruling out
print temperature, fan cooling, infill density, wall count, and
print speed as causes.
2. A pin hinge + printed flex-tab spring -- the hinge itself worked,
but the tab kept breaking, either from its own fatigue or from the
force needed to free a fresh knuckle joint.
3. This version: pin hinge + separate rubber band spring + independent
anchor ring. Confirmed working on a real printed whistle body.
Version 1.1 changelog:
Update: rotation stop + reinforced neck
Two additions since the original proof-of-concept:
1. Rest-angle stop. The original design had no hard limit on how far the key swung open — it just rested wherever the elastic's tension happened to balance, which turned out to be a fairly wide ~45° off the tube, meaning a long finger reach to press it. Fixed by adding a small tail to the moving knuckle, on the opposite side from the blade. As the key opens, the blade lifts away from the tube while the tail (rigidly attached to the same rotating piece) swings the other way and strikes the ring's own outer wall — a see-saw, not a separate matching part. This caps the rest angle at a firm, repeatable ~30° instead of an unpredictable ~45°.
2. Reinforced knuckle-to-blade transition. The round moving knuckle (6mm) used to step down abruptly to a much narrower rectangular section connecting it to the blade — a classic stress concentration, and exactly where a test print snapped clean off during nail insertion. Fixed by tapering that transition: thicker (~5mm) right at the knuckle, narrowing back to the original 3.5mm a bit further up the blade. Widened only in thickness and height — not sideways — so it doesn't touch the fixed knuckles or affect how the hinge swings.
Version 1.2 Changelog
1) Increased size of pad on the blade.
2) Adhesive backed foam pad used; much superior to yoga mat material glued to the pad.
Notes for anyone printing this:
The stop tail contacts the ring, not your instrument's tube — so it's the printed part taking the repeated wear, not your whistle.
If you're printing in PLA rather than PETG, the stop feature was specifically designed with rounded contact edges and a wider contact patch for PLA's lower impact tolerance — worth keeping if you reprint with different filament.
Insert the hinge pin slowly with the knuckle supported from underneath — most of what breaks a hinge like this is bending force transmitted down the blade, not the bore resisting the pin.
## License
CC BY-NC-SA -- attribution required, non-commercial use only,
derivatives must stay open under the same terms.
## Credits
Design, testing, all the physical building and iteration by me.
OpenSCAD source developed with the help of Claude (Anthropic).