Creality Top Mount Spool Holder Adapter – CR-6 SE, CR-10 Smart & Ender 3
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A sturdy top mount adapter for the original spool holder on the Creality CR-6 SE, CR-10 Smart and Ender 3.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 45
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Open Community License v1.1
Top mount spool holder adapter for Creality printers 🧵🖨
This adapter allows you to mount the original Creality spool holder on top of the printer frame instead of on the side.
It was designed for printers such as the Creality CR-6 SE, CR-10 Smart and Ender 3, which normally have the spool holder mounted on the side of the printer. Moving the spool to the top can save desk space and may provide a cleaner filament path towards the extruder.
The original Creality spool holder slides into the rectangular opening at the front of the adapter, so there is no need to print or purchase a completely new spool holder.
Compatibility 🔧
The adapter is designed for printers using a similar aluminium top extrusion and the standard Creality spool holder, including:
Creality CR-6 SE
Creality CR-10 Smart
Creality Ender 3
Other similar Creality printers
Please check the dimensions of your printer frame and original spool holder before printing. Creality has produced several revisions over the years, because apparently keeping everything exactly the same would be far too convenient. 😉
Required hardware 🔩
For installation, you will need:
The original Creality spool holder
A suitable T-nut holder or T-nut
Matching bolts for mounting the adapter to the aluminium extrusion
The bottom of the model includes a dedicated recess for the T-nut holder.
Print orientation 📐
Print the model in the orientation shown in the included image.
The long mounting base should be placed flat on the build plate, with the spool holder section pointing upwards at an angle.
This orientation provides:
A large contact surface with the build plate
Stronger layer alignment in the load direction
Good strength around the angled support
Minimal support requirements
Recommended print settings ⚙
Suggested starting settings:
Layer height: 0.20 mm
Walls/perimeters: at least 4
Top and bottom layers: at least 5
Infill: 25–40%
Infill pattern: Gyroid, Cubic or Grid
Supports: Only where necessary
Brim: Optional
Material: PETG, ABS or ASA recommended
PLA may also work, but PETG, ABS or ASA is recommended for improved heat resistance and long-term strength.
The adapter supports the full weight of the filament spool, so this is probably not the ideal model for two walls and 8% infill. 😅
Installation 🛠
Place the T-nut holder or T-nut inside the recess on the underside of the model.
Position the adapter on top of the printer’s aluminium extrusion.
Secure the adapter using the appropriate bolts.
Slide the original Creality spool holder into the front opening.
Tighten all bolts before installing a filament spool.
Check that the spool can rotate freely and does not touch the printer frame or other components.
Additional information ℹ
This model was designed to reuse the original Creality spool holder. No additional spool shaft, bearings or complete spool holder assembly is required.
After installation, check whether the spool causes any unwanted movement or vibrations in the printer frame. A full 1 kg spool mounted on top can slightly increase frame movement, especially when printing with high acceleration settings.