TPU Fence Escape Stopper for Small Dogs
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A soft TPU ring that slides under your dog's existing collar and makes them just wide enough that the fence finally wins
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 70
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Pets
- Licencja
- Creative Commons — Attribution — Noncommercial
Our chihuahua, Ollie, likes to pop through the slats in the wooden fence and get in to trouble. That is why I made this model. Four slots split the ring into flexible segments so it opens up to go on, and you can dial the overall firmness at slicing time with infill — low for something soft and floppy, higher for a ring that holds its shape against a determined shoulder-first shove. It is strongly recommended you print this in 95A TPU.
Designed for dogs under roughly 25 lb. Above that, a dog is strong enough to fold a 10%-infill TPU ring — and if a dog that size is fitting through your fence gap, you have a bigger problem than a printed collar can solve.
Pick your size
Two measurements decide this: your dog's neck, and your fence gap.
Measure the neck circumference snug, the way you'd fit a collar, and match it to the table. Then check the outer diameter against your fence gap — the ring blocks any gap narrower than its OD.
Size | Neck circumference | Blocks gaps up to | Ring thickness | Overall height | Est. filament |
|---|---|---|---|---|---|
XS | 8" | 6" (152 mm) | 0.333" | 28.5 mm | ~70 g |
S — Ollie's size | 10.2" | 7" (178 mm) | 0.333" | 28.5 mm | ~92 g |
M | 12" | 7" (178 mm) | 0.400" | 30.2 mm | ~100 g |
L | 14" | 8" (203 mm) | 0.450" | 31.4 mm | ~142 g |
XL | 16" | 8" (203 mm) | 0.450" | 31.4 mm | ~126 g |
If you're between sizes on the neck measurement, go down — TPU plus the four flex slots give you about a quarter inch of give in either direction.
Every size fits a 220 mm bed. XS needs 160 mm, S and M need 185 mm, L and XL need 210 mm.
The larger sizes are printed thicker on purpose: a wider ring loses stiffness fast, so M through XL are 0.4–0.45" instead of 0.333" to keep them from folding under a determined push.
Each ring carries its size marking on the underside, so once you've printed a couple you can still tell them apart six months later.
One thing that looks like a typo but isn't: Large uses more filament than Extra Large. The two share the same 8" outer diameter, and Large has the smaller neck bore — so there's simply more ring between the two edges. Same story between Small and Medium at 7". Print time tracks filament, not size letter.
Print settings
Material: TPU (95A recommended; softer shore = softer ring)
Layer height: 0.2 mm
Walls: 4
Infill: 5–10% — lower for a softer ring, higher for a firmer one
Supports: None needed — the wall taper is a 75° overhang
Orientation: Flat, ring face down, wedge wall pointing up
Speed: 20–30 mm/s (slower is more reliable with flexibles)
Brim: Recommended for adhesion
Time: Roughly 8–12 hours depending on size and infill
Nozzle Size: I've had luck with 1mm nozzles and TPU. Bigger nozzles require fewer walls typically and fewer layers. So in theory, there are fewer fail points. It's not required, but if you have a bigger nozzle, it might be a good time to experiment.
Fitting it
Flex the ring open at the slots — it spreads enough to pass over the head.
Settle it where a collar would normally sit, marked face down, with the tapered wall seated against the neck and the ring lying flat across the chest and shoulders.
Check the fit: two fingers should slide between the wall and the neck. Snug enough to stay put, loose enough that it isn't pressing.
Watch the first yard session at the gap that was the problem, and confirm it stays seated through a full-speed run and a good shake.
A note on safety
This is a physical barrier, not a substitute for supervision. Anything worn around a dog's neck can catch on fencing, brush, or another dog during play, and a ring this size adds surface for that to happen.
Importantly, this has no breakaway mechanism — it's a continuous ring, so if it snags on something it will not release on its own. Only use it while you're around to help, and take it off for crate time, car rides, unsupervised yard time, and play with other dogs. Check the fit as coats change with the season, and check that your dog can still reach the food and water bowls comfortably — if not, size down or take it off at mealtimes.
If you'd rather have a release mechanism, wear it alongside a breakaway collar so there's still something on the neck that gives under load.
