Teetotum Set — Spinning-Top Dice (d6 · d8 · d10 · d12, 2-Colour)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
The pre-dice gambling top, four ways: spin it, let it topple, read the up-facing number. d6/d8/d10/d12, each a 2-colour
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 18
- Wydruki
- 0
- Wyświetlenia
- 60
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Board Games
- Licencja
- Creative Commons — Attribution
A teetotum is the ancestor of dice — a numbered top you spin instead of throw. Give it a flick, let it topple, and read the number on the face pointing up. This set gives you four of them: a d6, d8, d10 and d12, all from one parametric source.
Each top is a faceted spinning body with a number engraved on every vertical face, a rounded pivot to spin on, and a pinch-and-twist stem on top. They print point-down and spin true off the bed.
What's in this listing
d6 — 6-sided top, 2-colour, break-away support included
d8 — 8-sided top, 2-colour, break-away support included
d10 — 10-sided top, 2-colour, break-away support included
d12 — 12-sided top, 2-colour, break-away support included
SCAD — parametric OpenSCAD source
The break-away support — this is the clever bit
A spinning top lands on a near-point pivot: almost nothing to stick to the bed, and a tall body that wants to tip over mid-print. So each STL ships with a modelled snap-off support pad already built in — you do NOT turn on slicer supports.
The trick is that the support never actually touches the model. Every contact stops one layer height (about 0.2 mm) short and lets the printer bridge the air gap:
A wide bed disc gives a brim-like footprint for adhesion.
A central column rises to a tiny platform that stops 0.2 mm under the pivot tip — the first layer bridges onto it.
Six outrigger fins stand just off the cone (never fused to it), bracing the tall body against tipping by proximity alone.
Because nothing is welded to the surface, the whole pad peels away in one piece (a twist of pliers on the fins) leaving no torn scar — just a faint dimple on the very bottom point of the pivot, which you sand back to a sharp spin-point anyway. That is the whole difference from generic slicer supports: those fuse and tear the surface; this bridges and lifts off clean.
Tuning: the air gap is set to 0.2 mm (one 0.2 mm layer). If the pad detaches mid-print, your gap is too big — regenerate from the SCAD with a smaller support_gap. If it fuses and won't peel, raise it. Match it to your layer height.
Two-colour (numbers pop)
Each file is a combined STL with two named solids — the body (with its support) and the digit inlays, coordinates locked. In Bambu Studio: Import, right-click, Split to Parts, then assign the two filaments. The engraved numbers fill flush in the second colour. Prefer one colour? Print it as-is — the numbers are recessed and still read fine.
Print settings
Orientation: point-DOWN, exactly as the STL sits (stem up). Don't re-orient.
Supports: OFF in the slicer — the support is already in the model.
0.2 mm layers, 3 walls, 15% infill, PLA or PETG.
After printing: peel the pad off, sand the pivot tip to a point, spin.
Fully parametric
Open the SCAD to change body width, face count (faces = 6/8/10/12), stem, font, engrave depth, or the whole support (support, support_gap, support_strut_n). Part selector: body / digits for each colour; all for the single-colour preview.
License: Creative Commons — Attribution. Personal + commercial use OK, attribution appreciated.
