1 / 7
ATX Bench Power Supply – "Fritanga 3000" (3D Printed) — zdjęcie 1
1 / 7

ATX Bench Power Supply – "Fritanga 3000" (3D Printed)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Turn a dead PC power supply into a variable bench PSU. 3D printed case, fuses, USB & protoboard outputs.

Ocena
0 / 5
Polubienia
53
Pobrania
104
Wydruki
0
Wyświetlenia
979
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Please like!!

I would love to see your makes!

ATX Bench Power Supply – "Fritanga 3000" (3D Printed)

Turn a dead (or spare) PC power supply into a proper variable bench power supply. This is a fully 3D printed enclosure that converts an ATX PSU into a bench power hub with fixed rails, a variable output, fused outputs, USB ports and breadboard headers.

The name? Fritanga is Argentine slang for a greasy fry-up. Given how many circuits this thing is going to fry during late-night experiments, it felt appropriate. Model number included, for that professional touch.

Features

  • Variable output 0.6–30V via an XY-SK35H buck-boost module with V/A/W display and adjustable current limit

  • Fixed rails broken out to banana jacks: 3.3V, 5V, 12V and −12V (pair with 12V for a ±12V symmetric supply)

  • High-current 12V output with paralleled rails for higher amperage

  • Individually fused outputs — one fuse per rail on the back panel, using 5x20mm screw-cap fuse holders and an assorted fast-blow fuse kit

  • 2× USB 5V ports for powering boards (Arduino, ESP, etc.) with their factory cables

  • Breadboard headers for 3.3V, 5V and variable, with a shared ground rail

  • Power-good LED indicator driven from the PSU's PWR_OK line

  • Forced-air cooling for the variable module under load

  • Engraved labels, no stickers

  • Magnetic fan grille — the fan cover snaps on with embedded magnets for tool-free cleaning access

⚠ Before you start

You're working with a PC power supply. Even though the outputs are low voltage, the primary side carries mains voltage and the capacitors stay charged even when unplugged. Never open the PSU casing while it's connected, and discharge the caps before working inside. This project assumes you're comfortable with soldering and basic electrical safety — if you're not, get help for the mains-side steps.

Bill of materials

Main electronics
  • A working ATX PSU (I used a Performance DX-ATX550)

  • XY-SK35H buck-boost module (0.6–30V, 4A, 35W) — eBay

  • 5× panel-mount 5x20mm fuse holders, screw cap, 10A — eBay

  • Assorted 5x20mm fast-blow glass fuse kit — eBay

  • Panel-mount banana jacks (6 colors + 2 black)

  • 2× panel-mount USB-A female connectors

  • ON/OFF toggle switch, blue LED + 220–330Ω resistor

  • 12V fan (recycled)

  • M3 brass heat-set inserts (5mm OD) + M3x8 screws

  • 12× neodymium magnets, 5×20mm (for the removable fan grille)

3D printed

  • Front panel, body + top cover

  • Body-color filament + a contrast color for the engraved lettering

Consumables: heat-shrink, wire (recycled from the PSU itself), solder.

⚠ Compatibility notes between PSUs

This is what varies most from one ATX supply to another — read this before wiring:

  1. The wire color code isn't always respected. Before wiring, measure every wire against a black one. Some supplies swap or relabel rails. Don't trust the printed color.

  2. A sense wire may or may not be present. If yours has one coming from the "+3.3Vs" pad on the board, it splices to the +3.3V rail (orange) — it's not an output.

  3. Rail currents vary by model. Check your PSU's label and adjust the fuse values accordingly.

  4. Some PSUs won't start without a minimum load. If yours doesn't power up unloaded, add a ~10Ω 10W bleeder resistor on the +5V rail.

  5. ATX casing dimensions vary. The model is parametric — adjust the PSU dimensions before printing.

Print settings

Overall this is an easy print. No supports are needed if you follow the orientations: front and back panels with the cut-out face on the bed, body with the lettering face down.

  • Material: PLA or PETG (PETG if you expect internal heat; PLA is fine for normal use with the fan)

  • Layer height: 0.2mm

  • Perimeters: 3–4

  • Infill: 15–20%

  • Supports: none

Two-color engraved lettering (the one tricky part) ⚠

The body prints the lettering first (fuse values and labels sit against the bed), then the rest. To get the letters and the panel field perfectly flush, in one uniform piece, there's a manual step during printing:

  1. Load the letter-color filament first.

  2. Print the first layer without brim— this is only the lettering (the fuse values, etc.).

  3. Right there, before it continues, manually lower the nozzle Z-offset (baby stepping) by 1 to 1.5 layers. This makes the panel field bite onto the letters so everything ends up at the same level, with no step or seam.

  4. Change filament to the body color and let it finish.

Without that offset tweak you get a small step or a visible seam between the letters and the field; with it, the piece comes out as a uniform two-color plate.

Note: the exact value (1 vs 1.5 layers) depends on your printer and first-layer adhesion. If it sinks too much, lower less; if the step shows, lower a bit more. Test once and adjust.

Assembly

1. Prep the PSU. Identify and measure all wires. Set aside the control wires (green PS_ON, gray PWR_OK, purple 5VSB) and the sense wire. Cut and salvage the wires you won't use (SATA/Molex) for internal wiring; individually insulate every live end you discard.

Don't be afraid, its really simple. It just takes some time 

2. Print the parts. Front and back flat, letter face on the bed, with the filament change described above. No supports.

3. Install the inserts. With a soldering iron, into all panel-joint bosses and the PSU/fan anchors. Pilot hole 4.0–4.2mm.

4. Mount the components. Front: banana jacks, USB, toggle, SK35H module. Back: 5 fuse holders, the PSU's fan, IEC inlet. The power LED goes under the fan, inside the PSU.

Breadboard headers. For the breadboard outputs, I bought 40-pin female header strips and cut them into 20-pin segments. Each segment is soldered to a piece of protoboard (perfboard), which handles the wiring on the back and gives the connectors a solid base. The assembled protoboard is then held in place behind the front panel with hot glue, so the headers stay put when you plug and unplug jumpers. This way you can feed a breadboard directly with standard male-male jumper wires straight from the panel, no flying leads.

5. Wire the outputs. Each rail passes through its fuse before reaching the jack:

Wiring note: the ground carries the same number of wires as the positive on each rail. With 20 AWG count on ~3–4A per wire; with 18 AWG, ~5–6A. Splices soldered and heat-shrunk, never twisted.

6. Wire the control. Green (PS_ON) to the toggle → GND. Gray (PWR_OK) → resistor → blue LED → GND. The SK35H is fed from +12V (with its 5A fuse on the input).

7. Common ground. All blacks, the SK35H's input/output GND, and every black jack go to a single COM bus, which also ties to chassis ground via the IEC inlet.

8. Test. Before final assembly, power up and check every output with a multimeter: polarity, voltage, and that the indicator LED lights. Only then assemble for good.

Cooling detail

The build uses two fans working together as one airflow path, not two independent fans:

PSU fan (extractor). The ATX supply's original fan stays where it is, on the back panel. By design it pulls air out of the enclosure and exhausts it out the back. This is your exhaust — don't change it.

SK35H fan (intake). A recycled 12V fan mounted right above the variable module blows inward and down onto the module's heatsink. The XY-SK35H runs at 35W and the manufacturer recommends forced-air cooling; without it, it throttles or overheats under high load.

Running them this way gives you a single, coherent airflow: air enters at the top over the module → sweeps across the interior → exits through the PSU at the back. The enclosure stays under slight positive pressure, which keeps dust out and prevents a dead zone forming right over the module you're trying to cool.

Getting it right:

  • Check the arrow on the fan frame for flow direction before screwing it in — as a rule, air exits on the label side. The new fan must blow in.

  • Align it with the heatsink fins so it blows onto the fins, not past them. Leave ~10–20mm clearance.

  • Power: wire the fan to the 12V rail, after PS_ON, so it starts with the supply. If the recycled fan is noisy, try it on 5V — it'll usually still spin and it's plenty for 35W.

  • Air intake matters. Add ventilation openings near the intake fan, and don't over-open elsewhere — otherwise the fan pulls air from the nearest hole and doesn't sweep the interior. Keep the intake grille's open area equal to or greater than the exhaust.

  • The PSU cover must be on. The ATX fan only cools properly with the metal casing closed — the sheet metal forms the duct that forces air across the transformers and heatsinks. Open, it cools worse.

Tagi