Smaller Tamagotchi Paradise to UART to USB Adaptor
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Connect your tamagotchi paradise to USB and do playdates with people online or get items
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 19
- Wydruki
- 0
- Wyświetlenia
- 475
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Video Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a remix of the Pogo Pin version of the connector, the only difference really is a better fit right off the printer and that it's all 1 tiny box instead of just the connector.
This is primarily for use with https://tools.bbamorachi.us/ Tamagotchi Paradise tools.
here's the pogo pins i bought.
(Treedix 30PCS Gold Plated Spring Loaded Thimble Pogo Pins Probes 2mm Dia 7.5mm Height Pogopin Header Target Connector Through Hold PCB Test Pin, Thimble Signal Pin )
i used the 7.5mm ones.
https://www.amazon.com/dp/B0BJPMWW5J
these are nice and cheap and come in a 4 pack.
(4pcs Type-C FT232RL USB to TTL Serial Converter Adapter Module 3.3V 5.5V FT232R Breakout Mini USB to TTL Adapter Board for Arduino (4pcs) )
https://www.amazon.com/dp/B0FLXZ6W2M
my suggestion is to just make 4 of these and give them to your friends. the more that are out there the more people we can do stuff with.
I highly recommend. the guide on building a adapter from catalystwyrm
https://ko-fi.com/s/0729d5c04d
They offer the PDF for free and will go over the basic concepts of wiring one up, not for this print but should give you an idea of what your doing.
there's a couple of tricky parts, the first is removing the header pins from the SERIAL TTL usb. i took some wire and just cut a piece long enough to go across all the pins and flowed a lot of solder till all the pins were connected. this distributed the heat and allowed all the pins to flow at once and just fall out. repeat with the voltage jumper pins as well.
Voltage has to be set to 3.3v so use some wire or create a solder bridge to connect that in place of the jumpers we removed.
after that cut 3 pieces of wire. i recommend 30awg wire or even smaller about 3inches long, there's not much voltage or anything so it doesn't need to be thick wire and the thicker it is the harder it's gonna be to attach.
https://www.amazon.com/JESSINIE-8-Color-Electronic-DM-30-1000-Wrapping/dp/B0BJ86D1Q3 (what i used for these)
after that i put the pogo pins in the print and quickly hit the top of the pins with some solder to tin those up in place. (this will melt the print a little, in most cases this will lock the pin in place. if not glue might need to be used after. if your worried about melting the print use some pliers to hold the pin and solder the wire to it first out of the case, then once it's attached maneuver it into the print and glue it in.
once the pins are soldered and they got wire connected and in place, solder the Serial TTL adaptor to the wires. your middle pogo pin is always gonna be ground, so solder that to ground and then RX and TX on the other pins (look at the PDF to make sure there's a pin out there) i guess and if it's wrong i just go and swap the wires after and before assembly.
now is a good time to test. your wires are on the pogo pins and connected to the board. go to. https://tools.bbamorachi.us/ and pick the serial port that comes up and try a playdate. if it fails double check your wires. try swapping RX an TX and make sure ground is actually connected to the ground pin on the board. once you confirm operation outside of the case and it works. the board can be maneuver in and slid into place. secure it by putting some hot glue on each corner by the USB port. and fill in the back so pressing in the usb cable won't let the board move around. after that just shove the wires inside.
now just glue the top on and it should be good to go.
I added a self adhesive wheel weight to this last one i built. they're cheap and give it more of a premium feel. 2 of them should fit inside but just 1 should do the job and make it feel a bit heavier and substantial so i highly recommend adding it if you want a better feel for it.
https://www.amazon.com/dp/B0FNW85HMP
if you have fitment issues, with it not connecting securely to the Tamagotchi, you can set your soldering iron to 120 for PLA and 130 for PETG, and put your iron behind the part of the connector that holds onto the peg and bring it in just slightly, and let it cool then test the fit again and it should be tighter. do the same for the other one for an even tighter fit if needed.
The model orientation for the print is already setup for you. you wanna use small layers, as well as supports.
if it worked well for you let me know.
https://bsky.app/profile/codenamegamma.com
we could also maybe do a playdate if you like.