Playmobil Steck Castle Floor Connector – Part 3002915 / 30029150
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a 3D-printable replacement for PLAYMOBIL part 30029150
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 23
- Wydruki
- 0
- Wyświetlenia
- 74
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a 3D-printable replacement for PLAYMOBIL part 30 02 9150, also identified by the shorter mould number 3002915.
The original piece is known as the Floor Connector. It is used to connect and support floor or walkway sections in the classic PLAYMOBIL Steck castle construction system.
This connector can be found in several vintage medieval and castle sets, including PLAYMOBIL 3666, 3667 and 3888. Before printing, compare the shape and part number with the original component you are replacing.
I tried to keep the model as close to the original part as possible while making minor adjustments where necessary to improve its strength and reliability when printed using an FDM printer.
The download includes:
- STL file for use with any compatible slicer
- Optimized 3MF project
- Recommended side-printing orientation
- Automatic supports configured for the internal overhangs
- Brim enabled for improved bed adhesion
The connector contains internal recessed areas and overhangs that require support material in the supplied orientation. The included 3MF has supports configured to reach these areas while remaining reasonably easy to remove.
Printer calibration and material shrinkage can affect the final fit. Test-fit the part gently and lightly sand only the necessary contact surfaces when minor adjustment is required.
This is a fan-made replacement part and is not an official PLAYMOBIL product. It is not affiliated with, sponsored by, licensed by or endorsed by PLAYMOBIL. PLAYMOBIL is a trademark of its respective owner and is referenced only to describe compatibility.
Digital files only. No physical product is included.
## Settings and manufacturing instructions
Print the model in the supplied side orientation. Do not use the slicer's automatic orientation function, as this may place the internal overhangs in a less printable position.
Recommended settings:
- 0.4 mm nozzle
- 0.12 mm layer height
- 0.20 mm initial layer height
- Arachne wall generator
- 5 walls/perimeters
- 6 top layers
- 6 bottom layers
- 18% gyroid infill
- Supports enabled
- Normal automatic supports
- Snug support style
- Supports placed everywhere, not build-plate-only
- 30° support threshold
- 3 top support-interface layers
- 0.20 mm top support distance
- 0.35 mm support/object XY distance
- 0.45 mm support-interface spacing
- 5 mm outer brim
- 0.10 mm brim/object gap
- Approximately 50 mm/s outer-wall speed
- Approximately 5,000 mm/s² outer-wall acceleration
PLA or PLA+ is recommended for the easiest printing and support removal. PETG may also be used when slightly more flexibility is preferred, although it can make the internal supports more difficult to remove.
The recessed internal channel and unsupported overhangs require support material in the supplied orientation. Allow the print to cool completely before carefully removing the supports.
Use narrow pliers or a suitable support-removal tool to extract material from the internal areas. Avoid twisting the tool against the thinner walls or connection edges.
Clean the build plate before printing. The 5 mm brim helps stabilize the part and reduces the possibility of an edge lifting during the print.
After the print has cooled, carefully remove the brim and test-fit the connector gently. When adjustment is required, lightly sand only the affected contact surfaces rather than scaling the entire model.