Ultimate Aerobar Spacer Kit V2 56 pcs 15-75mm | Parametric Fusion 360
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Stackable aerofoil shaped aerobar spacer kit 15mm - 75mm height, designed in Fusion 360 parametrically
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 68
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor Sports
- Licencja
- Creative Commons — Attribution — Share Alike
Stackable aerofoil shaped aerobar spacer kit 15mm - 75mm height, designed in Fusion 360 parametrically Currently for 31.8mm handlebars, and 50mm and 42mm hole spacing. Might be compatible with Profile Design.
WARNING: DO NOT USE 4.4 GRADE BOLTS!!! For grade refer to the table below
DISCLAIMER: USE AT YOUR OWN RISK!!! Plastic is plastic and plastic breaks
NOTES:
I haven't fully tested them to know if all heights are strong enough for all conditions but I've seem people using similar 3D printed ones so use your own judgement and test it by trying to bend them while stationary (you don't want to find out if they are strong enough at 50kmh in a pothole haha)
I include a set wider spacers (W1.2) for extra strength. I recommend it for higher stacks. There is Fusion 360 parameter to make them as wide as you want if you want more strength.
It has cutout in the middle for Di2 shifter cables (for at least 3 of them)
Assembly:
I would highly recommend using original metal clamps (I include 3D clamp but I don't know its strength and failure would be bad)
You will need some grippy assembly paste to increase friction between clamp, spacer and handlebar. Electrical tape most likely won't be enough. Maybe some thin rubber would be ok
Bolts:
M6 Bolts. 8.8 Grade or higher (see table below)
You'll need ~10-15mm longer bolts than spacer height (if you use original clamp because ~10mm threads into aerobar)
With 3d printed spacer you''l need ~35-40mm longer bolt than spacer height
For higher stacks use stronger grade bolts
Use blue Loctite to secure bolts from loosening due to vibration
Print settings:
Material: PETG (or stronger). (NO PLA)
6 walls with 50% grid infill at 0.2mm seems solid
Support: Probably yes. Tho it can be printed without supports but either way you'd probably need to do a quick bottom arc scrape with a knife
If you need specific spacer you can edit parameters in Fusion 360 orI can generate it for you Also let me know if there are different hole spacing standards so I can include it here
Spacer Heights: 15 mm, 20 mm, 25 mm, 30 mm, 35 mm, 40 mm, 45 mm, 50 mm, 55 mm, 60 mm, 65 mm, 70 mm, 75 mm
Stack Height | Recommended Grade | Material | Why |
|---|---|---|---|
15 – 35 mm | A2-70 / Class 8.8 | Stainless or Steel | Low leverage; stainless handles sweat well. |
40 – 55 mm | Class 8.8 / Grade 5 Ti | Steel or Titanium | Moderate bending loads; Ti stops corrosion. |
60 – 75 mm | Class 10.9 / 12.9 | High-Grade Alloy Steel | High bending lever arm; standard stainless will yield. |