1 / 7
Playmobil Steck Castle Wall End Male Connector 3007609 (30 07 6090) - Replacement Part — zdjęcie 1
1 / 7

Playmobil Steck Castle Wall End Male Connector 3007609 (30 07 6090) - Replacement Part

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Playmobil Steck Castle Wall End Male Connector – 3007609 / 30 07 6090

Ocena
0 / 5
Polubienia
2
Pobrania
20
Wydruki
0
Wyświetlenia
61
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Building Toys
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Two versions of this wall-end connector are included.
The first version is designed to look as close as practical to the original Playmobil Steck part.
I also made a second optimized version that uses less filament and requires almost no support material, but its simplified geometry does not look as close to the original.

All photos showing a real 3D-printed part are of the original-style version, because that is the only version I have physically printed so far. The optimized low-support version is shown using digital renders.

This independently recreated replacement is intended for vintage Playmobil Steck-System medieval castle walls. The original component is commonly described as a wall-end connector, male wall connector, single-sided Steck connector or Mauerabschluss.

It is commonly associated with Playmobil castle sets including:

  • 3665

  • 3666

  • 3667

  • 3839

The connector finishes the end of a castle wall section and provides the projecting male connection features used by the Steck construction system. It can be useful for restoring an incomplete castle, replacing a broken connector, expanding a custom castle layout or keeping a spare component available for future repairs.

TWO INCLUDED VERSIONS

Original-style version

This version reproduces the appearance and construction of the original component as closely as practical, including its segmented stone exterior and projecting connection features.

  • Closest visual match to the original part

  • Recommended for restoration and display

  • Requires support material

  • Uses the narrow side-printing orientation supplied in its 3MF

  • This is the version shown in the finished-print photographs

  • This is the only version I have physically printed so far

Optimized low-support version

This alternative has simplified geometry intended to make FDM printing easier and more economical.

  • Uses less filament

  • Requires almost no support material

  • Easier support cleanup

  • Uses a separate, intentionally tilted printing orientation

  • Designed to retain the functional connection dimensions

  • Does not look as close to the original component

  • Has not yet been physically printed by me

  • Shown in the listing using digital renders

INCLUDED FILES

  • 3007609.stl – original-style version

  • Prepared original-style 3MF with 0.08 mm layer height, snug supports and a 15 mm zero-gap brim

  • 3007609_optimized.stl – lower-filament, low-support version

  • Prepared optimized 3MF with 0.08 mm layer height, minimal automatic supports and a 15 mm zero-gap brim

FIT INFORMATION

Dimensional accuracy can vary between printers, materials and slicer profiles. Older original castle components may also have wear, deformation or manufacturing variation.

Remove all brim and support material before attempting installation. Test-fit the connector gently and never force it into an original wall section.

If the fit is slightly tight, carefully clean the contact surfaces with a fine file, sanding stick or fine-grit sandpaper. Remove only a small amount of material at a time.

Calibrating filament flow, elephant-foot compensation and dimensional accuracy is preferable to scaling only one axis. Uneven scaling can change the spacing between the upper and lower connector features.

Because only the original-style version has been physically printed so far, the optimized version should be considered an alternative experimental design until you have confirmed its fit on your own printer.

Original walls, castle sections, figures and accessories shown in presentation photographs are not included.

PART-NUMBER SEARCH VARIATIONS

This component may be found online using several number formats:

  • 3007609

  • 30076090

  • 30 07 609

  • 30 07 6090

TRADEMARK NOTICE

This is an independently recreated, unofficial compatible replacement part. PLAYMOBIL is a trademark of its respective owner. This design is not affiliated with, endorsed by or sponsored by the trademark owner.

3D PRINTING SETTINGS

Two different versions are included, and each has its own prepared 3MF project.

Use the orientation saved in the matching 3MF file. Do not use the slicer’s automatic orientation function, do not automatically place the largest face on the build plate and do not copy the orientation from one version to the other.

The two versions use deliberately different orientations.

VERSION 1 – ORIGINAL-STYLE MODEL

The original-style model is intended to reproduce the appearance of the original connector as closely as practical.

It prints upright on a narrow side in the supplied 3MF orientation. This preserves the external appearance and functional features, but support material is required.

  • Use the supplied side orientation

  • Do not rotate it onto its broad decorative face

  • Supports must remain enabled

  • Supports must be allowed everywhere, not only from the build plate

  • Keep the 15 mm zero-gap brim for the first print

  • Allow the print to cool fully before removing it from the plate

The narrow contact area makes the brim particularly important. A dirty build plate, insufficient first-layer adhesion or excessive cooling during the first layers may allow the long part to lift or detach.

This is the version shown in the finished-print photographs and the only version I have physically printed so far.

VERSION 2 – OPTIMIZED LOW-SUPPORT MODEL

The optimized model has simplified geometry and a separate orientation designed to reduce filament consumption and support material.

Its slight tilt in the supplied 3MF is intentional.

  • Use the separate optimized 3MF orientation

  • Do not flatten the model automatically

  • Do not reuse the original-style model’s orientation

  • Leave automatic supports enabled

  • The slicer should generate little or almost no support material

  • Small support areas may still appear beneath individual connector details

  • Keep the supplied 15 mm brim for the first attempt

The optimized model does not look as close to the original part and has not yet been physically printed by me.

PREPARED PROFILE

The supplied 3MF projects were prepared for a:

  • Printer: Bambu Lab A1

  • Nozzle: 0.4 mm

  • Build surface: Textured PEI Plate

  • Material profile: PLA

  • Print sequence: By layer

For a different FDM printer, import the relevant STL and reproduce the orientation and settings below.

RECOMMENDED QUALITY SETTINGS

  • Nozzle diameter: 0.4 mm

  • Layer height: 0.08 mm

  • Initial layer height: 0.20 mm

  • Wall generator: Arachne

  • Walls/perimeters: 3

  • Top layers: 9

  • Minimum top-shell thickness: 0.80 mm

  • Bottom layers: 7

  • Infill density: 12%

  • Infill pattern: Gyroid

  • Wall order: Inner wall before outer wall

  • Print sequence: By layer

  • Scale: 100%

SPEED AND ACCELERATION

  • Outer-wall speed: 60 mm/s

  • Outer-wall acceleration: 2,000 mm/s²

  • Default acceleration: 4,000 mm/s²

  • Initial-layer speed: 50 mm/s

Slower outer walls may improve the appearance of the segmented stone surfaces. Reduce the speed if your printer shows ringing, poor corners or inconsistent narrow features.

SUPPORT SETTINGS

The supplied profiles use the following support settings:

  • Supports: Enabled

  • Support type: Normal automatic

  • Support style: Snug

  • Support placement: Everywhere

  • Build-plate-only supports: Disabled

  • Support threshold angle: 30°

  • Top support-interface layers: 2

  • Bottom support-interface layers: 0

  • Support-interface spacing: 0.30 mm

  • Top support Z distance: 0.16 mm

  • Bottom support Z distance: 0.16 mm

  • Support/object XY distance: 0.45 mm

  • Support base-pattern spacing: 3 mm

For the original-style version, do not change support placement to build-plate-only. Some connection features may require support that cannot originate directly from the plate.

The optimized version is designed to require almost no support material, but automatic supports should remain enabled so that the slicer can protect any small unsupported details.

BUILD-PLATE ADHESION

  • Brim type: Outer brim

  • Brim width: 15 mm

  • Brim/object gap: 0.00 mm

The zero-gap brim provides the strongest possible connection to the model. It will require more cleanup than a separated brim, but it helps protect this long, narrow component against detachment and end lifting.

Clean the build plate before printing. Fingerprints, dust or old adhesive residue can significantly reduce adhesion.

For the optimized version, the 15 mm brim is intentionally conservative. It may be reduced after you have completed a successful print on your own machine, but the supplied value is recommended for the first attempt.

PLA TEMPERATURES USED IN THE 3MF

  • Nozzle temperature: 220°C

  • Initial-layer nozzle temperature: 220°C

  • Textured PEI bed temperature: 65°C

  • Initial-layer bed temperature: 65°C

These are the values saved in the supplied PLA profile. Adjust them when required by your filament manufacturer, printer or build surface.

MATERIAL GUIDANCE

PLA or PLA+

PLA or PLA+ is recommended for:

  • Clean dimensional detail

  • Sharp connector features

  • Easier support removal

  • Lower warping risk

  • A finish closer to the original rigid plastic component

Use dry filament and a properly calibrated flow rate.

PETG

PETG may be used when slightly greater flexibility or impact resistance is preferred. However:

  • PETG supports may bond more strongly to the model

  • The zero-gap brim may be harder to remove

  • Fine strings may remain around the connector features

  • Dimensional fit may differ from PLA

  • Internal and recessed areas may require more cleanup

Adjust support distances and temperatures for your own PETG profile rather than using the PLA temperatures unchanged.

REMOVING THE PRINT

Allow the model and build plate to cool completely before removal. The connector is long and may bend if it is removed while still warm.

  1. Flex the build plate gently when possible.

  2. Lift the part gradually along its full length.

  3. Do not pull upward from only one end.

  4. Remove the outer brim using flush cutters, a deburring tool or a sharp craft knife.

  5. Keep cutting tools pointed away from your hands and away from the functional connector surfaces.

Because the brim has a zero-millimetre gap, small brim remnants may remain attached to the lower edge. Remove these completely before test-fitting.

SUPPORT REMOVAL

For the original-style version:

  1. Remove large external support sections first.

  2. Support the connector feature with your fingers while removing material around it.

  3. Use narrow needle-nose pliers or tweezers for recessed support material.

  4. Pull support material in the direction of the feature rather than twisting sideways.

  5. Avoid levering tools against thin projecting tabs or decorative ridges.

  6. Clean support marks with a fine file or sanding stick.

For the optimized version, only a small amount of support cleanup should normally be necessary. The exact amount depends on the slicer version, printer calibration and selected support threshold.

FINISHING AND TEST-FITTING

After removing the brim and supports:

  1. Inspect both projecting connector areas.

  2. Remove any elephant-foot expansion from the first layer.

  3. Check that no support material remains on the contact surfaces.

  4. Test-fit the part gently at 100% scale.

  5. Stop immediately if excessive force is required.

  6. Mark the exact contact point before sanding.

  7. Remove only a very small amount of material at a time.

  8. Repeat the test until the connector seats without being forced.

Do not hammer, twist or heavily bend the printed connector during installation. Excessive force could break the print or damage an original castle wall.

For consistently tight prints, calibrate flow rate, pressure advance, first-layer squish and elephant-foot compensation before changing the model dimensions.

This component is intended for hobby restoration, collection and display use. It is not a safety-critical or structural load-bearing component.