Playmobil Steck Open Wall / Door Frame 3007671 (30076710) - 3666/3667 Castle Replacement Part
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Playmobil Steck Open Wall / Door Frame – Part 3007671 / 30076710
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 18
- Wydruki
- 0
- Wyświetlenia
- 56
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Building Toys
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Restore an incomplete or damaged vintage castle with this printable replacement for the Playmobil Steck one-unit open wall frame, commonly identified as part 3007671, 30076710 or 30 07 6710.
The model recreates the open rectangular frame, diagonal strengthening braces and surrounding Steck connection features of the original-style component. It can be used as an open doorway or structural frame section in compatible vintage castle and medieval building assemblies.
The part prints as one complete piece and is designed to be printed flat without support material.
INCLUDED FILES
3007671.stl – full-scale printable model
3007671.3mf – prepared high-quality FDM project with the recommended flat orientation, 0.08 mm layer height, no supports and a 5 mm outer brim
COMMONLY ASSOCIATED SETS
The original 30076710 frame is commonly catalogued for vintage Playmobil castle and medieval sets including:
3666
3667
5725
6412
7144
Some parts catalogues cross-reference the same general frame shape under the older number:
30028260
30 02 8260
Older sets, production runs and previously used components can have small dimensional differences. Compare the shape and connector locations with your existing castle before printing several copies.
USE AND FIT
This frame is useful for:
Restoring an incomplete vintage castle
Replacing a cracked or missing frame
Creating an open doorway section
Expanding a custom Steck castle layout
Repairing a medieval house or timber-frame building
Keeping a spare component available for future repairs
Printer calibration, material shrinkage and wear on original parts can affect the final fit.
Remove the brim completely and inspect every connection feature before installation. Test-fit the printed frame gently and do not force it between original wall components.
If a connection is slightly tight, carefully clean the affected surface with a fine file, sanding stick or fine-grit sandpaper. Remove only a very small amount of material at a time.
Calibrating filament flow and elephant-foot compensation is preferable to scaling only one axis. Uneven scaling may change the spacing between the surrounding connection features.
Dark-brown filament will provide an appearance closest to many original castle frames, although any color may be used for custom buildings and restorations.
Original castle walls, connectors, doors, figures and accessories shown in presentation photographs are not included.
PART-NUMBER SEARCH VARIATIONS
This component may be found online using several number formats:
3007671
30076710
30 07 671
30 07 6710
30-07-671
30-07-6710
The same or a closely related frame shape may also be catalogued as:
30028260
30 02 8260
TRADEMARK NOTICE
This is an independently recreated, unofficial compatible replacement part.
PLAYMOBIL is a trademark of its respective owner. This design is not affiliated with, endorsed by or sponsored by the trademark owner.
3D printing settings
3D PRINTING SETTINGS
Print the model flat in the orientation supplied in the 3MF file.
The large open frame should lie on its broad face, with the complete rectangular shape parallel to the build plate. Do not use the slicer’s automatic orientation function, and do not rotate the part upright.
The supplied orientation:
Requires no support material
Gives the frame a large build-plate contact area
Keeps the connector features aligned
Reduces unnecessary post-processing
Helps protect the narrow rails and diagonal braces during printing
The included 3MF was prepared for a Bambu Lab A1 with a 0.4 mm nozzle and textured PEI build plate.
For another FDM printer, import the STL and reproduce the orientation and settings below.
RECOMMENDED QUALITY SETTINGS
Nozzle diameter: 0.4 mm
Layer height: 0.08 mm
Initial layer height: 0.20 mm
Wall generator: Classic
Walls/perimeters: 6
Wall order: Inner wall before outer wall
Top layers: 9
Minimum top-shell thickness: 0.80 mm
Bottom layers: 7
Infill density: 25%
Infill pattern: Gyroid
Print sequence: By layer
Model scale: 100%
The high wall count strengthens the narrow outer rails, connection tabs and diagonal braces. Reducing the number of walls may save some material but can make these features easier to bend or break.
SPEED AND ACCELERATION
Settings used in the supplied project:
Outer-wall speed: 60 mm/s
Outer-wall acceleration: 2,000 mm/s²
Default acceleration: 4,000 mm/s²
Initial-layer speed: 50 mm/s
Initial-layer acceleration: 500 mm/s²
Slower outer walls may improve dimensional accuracy around the Steck connection features. Reduce speed if your printer shows ringing, rounded corners or inconsistent narrow rails.
SUPPORT SETTINGS
Supports: Disabled
Support material required: No
Raft: Disabled
The model is designed to print without supports in the supplied flat orientation.
If a slicer generates support material, first confirm that the model has not been automatically rotated or placed on an edge. Supports should not normally be necessary.
Adding supports may leave unnecessary marks on the frame and make the connector areas harder to clean.
BUILD-PLATE ADHESION
Brim type: Outer brim
Brim width: 5 mm
Brim/object gap: 0.10 mm
Skirt loops: 0
Clean the build plate immediately before printing. Dust, fingerprints or old adhesive residue may reduce first-layer adhesion.
Although the frame has a broad overall footprint, its individual rails are relatively narrow. The 5 mm brim helps keep the long edges and corner areas attached to the build plate.
For the first print, keep the supplied brim enabled.
If the ends begin to lift on another printer or material:
Clean the build plate thoroughly.
Check the first-layer calibration.
Reduce drafts around the printer.
Increase the brim to approximately 8–10 mm.
Reduce the brim/object gap if stronger attachment is required.
A zero-gap brim provides stronger adhesion but will require more edge cleanup.
PLA TEMPERATURES USED IN THE 3MF
Nozzle temperature: 220°C
Initial-layer nozzle temperature: 220°C
Textured PEI bed temperature: 65°C
Initial-layer bed temperature: 65°C
These are the temperatures saved in the supplied PLA project. Adjust them when required by your filament manufacturer, printer or build surface.
MATERIAL GUIDANCE
PLA OR PLA+
PLA or PLA+ is recommended for:
Clean dimensional detail
Sharp connector edges
Low warping
Easy brim removal
A rigid result similar to the original-style component
Straight, stable diagonal braces
Use dry filament and confirm that filament flow is calibrated.
Dark-brown PLA provides an appearance closest to many original castle frames.
PETG
PETG may also be used when slightly greater flexibility or impact resistance is preferred.
Be aware that:
PETG may produce more stringing around the open center
The brim may bond more strongly to the model
Connector dimensions may differ slightly from PLA
Fine edges may require additional cleanup
Excessive first-layer compression can make the fit too tight
Use a properly tuned PETG profile rather than copying the PLA temperatures unchanged.
FIRST-LAYER AND DIMENSIONAL ACCURACY
Because this is a functional replacement part, first-layer calibration is important.
Excessive first-layer compression may create an elephant foot around the lower edges and connection features. The supplied profile uses approximately:
Elephant-foot compensation: 0.075 mm
Inspect the bottom edges after printing. Remove any remaining first-layer flare before attempting installation.
If the frame repeatedly prints too tight:
Calibrate filament flow.
Check first-layer height and nozzle offset.
Confirm elephant-foot compensation.
Check X/Y dimensional accuracy.
Test the part again before changing its overall scale.
Do not scale only one axis unless you have measured the required correction carefully. Uneven scaling can change the spacing of the frame’s connection features.
REMOVING THE PRINT
Allow both the model and build plate to cool completely before removal.
The frame contains long narrow rails and diagonal braces that can be damaged if the print is pulled upward from one corner.
Recommended removal procedure:
Allow the build plate to return close to room temperature.
Remove the flexible plate from the printer when applicable.
Flex the plate gently along the length of the frame.
Release the outer edges gradually.
Avoid pulling upward on a diagonal brace.
Do not use a narrow brace as a handle.
Support the frame with both hands once it begins to release.
If a scraper is required, keep it nearly parallel to the build plate and work gradually around the outer brim.
BRIM REMOVAL
Peel away loose brim sections by hand.
Trim attached sections with flush cutters or a deburring tool.
Work gradually around the complete outer perimeter.
Pay particular attention to the connector tabs and narrow corner areas.
Remove all brim remnants before test-fitting the frame.
Smooth rough edges with a fine sanding stick if necessary.
Keep cutting tools pointed away from your hands and away from the functional connector surfaces.
FINISHING AND TEST-FITTING
After removing the brim:
Inspect the complete rectangular frame for warping.
Check that the diagonal braces are intact.
Inspect every projecting connection tab.
Clear the rectangular openings and recessed connection areas.
Remove strings or small blobs with tweezers or a fine file.
Check the lower surface for elephant-foot expansion.
Test-fit the frame gently at 100% scale.
Stop immediately if excessive force is required.
If a specific area is tight, mark the contact point and remove only a small amount of material from that location.
Do not hammer, twist or heavily bend the frame during installation. Excessive force could break the printed part or damage an original castle component.
This replacement is intended for hobby restoration, collection and display use. It is not a safety-critical or structural load-bearing component.