LX200 Classic OnStepX Conversion
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Convert mid 90's LX200 Classic electronics, gearbox, & motors into OnstepX
- Ocena
- 0 / 5
- Polubienia
- 7
- Pobrania
- 11
- Wydruki
- 0
- Wyświetlenia
- 266
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Physics & Astronomy
- Licencja
- Creative Commons — Attribution — Noncommercial
!!Work in Progress - Beta!!
Material: PETG, ABS or other strong non-PLA filament that won't melt in the garage.
Intro:
Many have said they would put together a good guide, though most have only left pieces to a puzzle that I used and/or had to improvise creating my on pieces. I hope to break that trend and publish a complete guide and files.
I upgraded my LX200 Classic to OnstepX to remove gear slop from old reduction gears as well as to use new technology as well as ASIAir for Astrophotography. On my second night of testing, I got as low as 0.44" guiding and usually bounced around 0.6" and 0.8". I am still working on the tuning.
I spent way too much time on this, though I hope that I save you guys a lot of time. I am also trying to refine this more to make it more user-friendly requiring less skills like crimping to complete.
Some of the photos are dated as I didn't take photos of every time, I made a change. I had a lot of revisions, especially after things started to come together. This includes most of the 3D printed items.
Todo:
1) Create nicer DEC cover.
2) Validate RA & DEC Spring supports via testers.
3) Created detailed schematic.
Electronics
The electronics are housed inside the base. I initially planned to get the E4 board with the external Wi-Fi antenna, but I accidentally ordered the wrong one. Surprisingly, I still get a solid signal even from inside the LX200 base.
The electronics tray is sandwiched between the base and the bottom plate—it sounds a bit strange, but it holds everything securely without issue. The tray has dedicated mounting spots for an RTC board, the E4 board, and a 3.3V voltage regulator. The regulator is held in place simply by the friction of three DuPont connectors plugged into it. The RTC (Real Time Clock) is meant to keep the time, some mounts don't have this as they are intended for astrophotography only. Though if you want to use this w/o a computer/tablet, then the RTC is recommended. I might modify my design as I don't like how the battery is housed in the base, making it a PITA to service, especially with larger scopes. Only issue is the face plate has limited space, especially with the large NEMA17 stepper taking up a lot more room than the stock motor assembly.
I used a level shifter because the PEC sensor operates at 5V, while the pin it plugs into isn't 5V-tolerant (stepping it down to 3.3V). I read that someone managed to run 3.3V directly to the PEC sensor successfully, but I opted for the level shifter. The PEC sensor is the only electronic component retained from the original build. After the level is shifted, the PEC output should go into TE header. If I could do this over again, I would use the Adafruit QT Level Shifter STEMMA QT board as it includes a shifter and a voltage regulator in one small compact board. While the level shifter is for I2C, we can hijack one of the 2 channels for this purpose. The only thing is you can't wire it directly to another QT board with a QT cable w/o cutting the clock and data lines. I added a 2nd board holder for the QT devices. Adafruit QT 5V to 3V Level Shifter Breakout - STEMMA QT / Qwiic : Adafruit Industries, Unique & fun DIY electronics and kits
There are two faceplate options available. I had to redesign the faceplate multiple times to resolve clearance issues, so I ended up publishing two versions: one with an integrated dew controller and one without. I used two RJ45 punch-down blocks and double-terminated each wire so the DEC cable uses all eight wires to distribute the current. I also wired it so that if the connections are reversed, the motor will simply spin in the opposite direction.
The USB 5pin header on the E4 doesn't have the standard pinout that most USB cables come as. I removed the red 5v power and wrapped it in shrink wrap to leave disconnect. One ground wire I used a spare 1x Dupont housing and plugged it into a nearby ground. I then shifted the two data wires closer to the ground pin so it lines up to the schematic. Be careful and double check the schematic for the header. See Header P15 in the E4 Schematic: https://github.com/FYSETC/FYSETC-E4/blob/main/hardware/FYSETC%20E4_V1.0%20SCH.pdf
OnStepX Fysetc E4 Board Documentation: [email protected] | Wiki
The Config.h for my setup is located here: https://github.com/windows2000bug/LX200ClassicOnStepX/blob/main/Config.h
Motor Assembly
The 3D-printed sleeve uses a screw to help support the axle, as both the 48T (DEC) and 32T (RA) cogs extend past the end of the stock axle. Both stepper motors use 12T pulleys paired with different belt lengths. This gives the DEC axis a 4:1 gear ratio and the RA axis a 3:1 ratio, as the 4:1 cog was too large to fit on the RA side.
To achieve a proper mesh between the worm screw and worm gear without binding or introducing backlash, you'll need to replace the stock springs on both axes. The DEC axis requires a much heavier spring, while the RA axis needs a lighter one.
I've included several design options in the STL files:
RA Axis: I used the largest option (far left in the model file), but I would advise using one of the alternative options provided instead.
DEC Axis: I included a flat design option. It should work well with the right spring tension, though I haven't personally tested this specific variant yet.
While my current configuration is functional, it isn't ideal, so I plan to refine these spring/bracket designs further in a future revision. I would appreciate people testing these out and letting me know.
Motor Brackets were designed by Chris K. of NovaLab Observatory and can be located here: https://www.NLobs.com/down/LX200.zip
For the brackets, I 3D printed them and used a drill press, jigsaw, files, and a lot of elbow grease to fabricate them by hand. The above zip ncluded the step files, if you have access to a CNC machine or use a service like JLCCNC. I did not make an inset on my mount so I had to replace the original mounting screws with longer 4-40 flat head screws. I think the original ones will be fine, if you have it CNC'ed to the step files fvrom Chris.
Video
Video of a quick demo of the unit, though I have refined some things as well as put a stronger spring into the DEC to remove the backlash.
Balancing:
Critical for imaging to maintain accuracy for tracking/guiding, you will need to properly balance the scope on 3 Axis. For me w/ me w/ an image train of a Starizona LF .7 reducer, focuser, OAG, spacer, & asi585mc, I put a 1lbs ankle weight around the fork w/o the DEC stepper. I also had to adjust my finder scope forward and I wrapped a 1lbs weight around it. I used a T-Track on the bottom of the scope where I attacked a 2.5lbs weight that I can move back and forth to adjust. Exact balance is l less important for visual astronomy. Here is a guide on balancing: Balancing for Imaging — Starizona
Bill of Materials
I think to replicate this project would be at least $250. I spent more than that as I ran into some dead ends. Though most of these parts come with way more than you need. I have enough left over that I could redo this project for again for under $100 as I would only really need 2 steppers and another E4 board.
Credits:
OnStepX
Developers & Community: https://onstep.groups.io/g/main
Stepper Bracket:
NovaLab Observatory (Chris K.)
Website: https://nlobs.com/
YouTube: https://www.youtube.com/@nlobs