1 / 1
Elfa - wired shelf hook. Karcher lances and equipment — zdjęcie 1

Elfa - wired shelf hook. Karcher lances and equipment

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Modified to match size and weight of Karcher lances

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
0
Wyświetlenia
39
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Garage
Licencja
Creative Commons — Public Domain

What this is

A remix of Brad's Hook for Container Store Elfa Closet System Wire Shelves, with a shorter bar. Six lengths.

The original hangs its cradle 75.65 mm out from the shelf clip. That is a lot of stand-off if the thing you are hanging is short, or if the shelf below is close. So the bar between the two ends is cut down, and nothing else is changed.

Both ends are Brad's, untouched. The clip still clips onto the wire the same way and the cradle still holds the same thing. Only the straight run between them is shorter.

The six lengths

Pick by how far you want the cradle to sit off the shelf. Width, height and the way it clips on are identical across all six — only the middle changes.

- 10 mm — 38.7 × 65.7 × 63.7 mm, 20.4 cm³

- 20 mm — 38.7 × 75.7 × 63.8 mm, 22.0 cm³

- 30 mm — 38.7 × 85.7 × 63.9 mm, 23.5 cm³

- 40 mm — 38.7 × 95.7 × 63.9 mm, 25.1 cm³

- 50 mm — 38.7 × 105.7 × 64.0 mm, 26.6 cm³

- 60 mm — 38.7 × 115.7 × 64.1 mm, 28.2 cm³

- the original, for comparison — 75.65 mm bar, 38.7 × 131.4 × 64.3 mm, 30.6 cm³

A warning about the 10 mm one. At that length the cradle's fillet almost touches the elbow. The geometry is sound and it slices clean, but there is essentially no gap left. If you need room to get something into the cradle, take the 20 mm.

How it was cut, and why you can trust it

This is not re-modelled. The mesh is imported into OpenSCAD, cut across the bar, and the far half slid back along the bar's own axis. That only works if the bar is a true prism, so here is the evidence that it is.

Its cross-section is constant over the entire straight run, and the run rises at a steady 0.5°. Fitting a line to the top edge and to the bottom edge over that span returns the same slope, 0.008727, with a maximum residual of 0.0000 mm. The far half is therefore moved by [0, -delta, -tan(0.5°) × delta], and the two cut faces land on each other exactly — no step, no kink, nothing to clean up.

Two numbers in the list above are the proof that every cut landed where it should:

- Volume goes up by 1.548 cm³ per 10 mm of bar, at every single step. That is the bar's 154.8 mm² cross-section and nothing else.

- Overall height goes up by 0.0873 mm per 10 mm, which is tan(0.5°) × 10 — the far hook riding up the tilt, exactly as it should.

A cut that had gone wrong anywhere would break one of those two lines. Every file reports manifold = yes and one part.

Files

Each length ships twice:

- .3mf — placed on the bed, opens straight into PrusaSlicer

- .stl — binary, for everything else

source/ has what you need for a length that is not in the list:

./make-3mf.py 35

Any value from 6 to 70. Stdlib Python — it needs openscad and prusa-slicer on your PATH and nothing else. model.scad opens in the OpenSCAD GUI too; bar_len is the only parameter worth touching.

source/elfa-pole-hook-source.3mf is Brad's hookpoleholder exported on its own, so model.scad has something to import. It is his geometry, unmodified, redistributed here under the CC0 he released it with.

Printing

PETG at 0.25 mm on a Prusa Core One, 0.4 mm HF nozzle. Brad printed the original in PLA — either is fine, this is not a heavily loaded part.

Supports are required. Both the clip and the cradle have real overhangs, and they need generated supports, not paint-on. Expect 21–30 g and roughly 1 h 05 to 1 h 25 depending on which length you pick.

Credit

The hook is Brad's — Hook for Container Store Elfa Closet System Wire Shelves (https://www.printables.com/model/1118038-hook-for-container-store-elfa-closet-system-wire-s), published 31 January 2025, specifically the hookpoleholder object in his Twomorehooks.3mf. He put it in the public domain, so this remix is CC0 as well.

Thanks, Brad.

Tagi