1 / 6
BC250 Case for three P12 fans and HP Flex Slot or Common Slot PSU — zdjęcie 1
1 / 6

BC250 Case for three P12 fans and HP Flex Slot or Common Slot PSU

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A relatively small case for the BC250 mining card. Uses three 120mm fans. The case measures 325x113x186mm (LxWxH)

Ocena
0 / 5
Polubienia
6
Pobrania
29
Wydruki
1
Wyświetlenia
926
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Codename GabeStation3


This is my take on a small-ish case that allows for good cooling of the BC250.
The dimensions are approx 325x113x186mm, which means it's a hair under 7L in volume.

EDIT: I just realized I didn't make a back case to fit the common slot PSU. Will fix as soon as I find the time. Flex slot fits. 

EDIT2: Added a case back side for the common slot PSU. Crisis averted.

After printing this on my SV08, things did not fit together all that well. After double checking the CAD I think it's because my printer just isn't calibrated. 
I had to file away a tiny bit of the inside corner of the fans to get everything to fit together nicely.
I'm not a good designer, but I had several requests (two actually) to release the files, so here they are in all their glory. Could it be better? Hell yes. Does it work in it's current state? Yes. 

Two 120mm fans mounted on the front heatsink and one on the back plate. There's about 12mm clearance between the back plate and the fan, so a small heatsink can be mounted if you feel the need to.

What you need to build:
1x BC250 (duh)
3x 120mm fans (Designed for Arctic P12 Pro PST)
1x PSU - HP common slot or flex slot
12x M4 threaded inserts of your choice
14x M4x16 screws of your choice
2x M4 hex nuts
1x M3 threaded insert
1x M3x6mm screw
1x Toggle switch, threaded ~6mm diameter, 8mm length, 10mm shaft
1x Bunch of cables for the PSU and toggle switch

Printing: Do whatever works for you. Supports are required for the PSU holder and recommended for the front case.

Print the parts, then add the heated inserts. M4 inserts to the fan screw holes in the bottom plate and PSU holder.
Add M3 insert where the BC250 mounts, at the back of the bottom plate.
Mount the two front fans on the bottom plate with the two middle screws.
Mount the back side fan with the lower right screw.
Remove the front and back brackets from the BC250. (Don't forget the tiny screw by the Display port connector!)
Mount the BC250 to the bottom plate. - M4 bolt and hex nut in the front and M3 screw in the back.
Mount the PSU in the PSU holder.
Place the PSU holder on top of the fans, attach it with the top middle screws. (Leave the four outer screws for now, they are are used to attach the fan grille)
Attach the PSU to the back side fan with the top left screw.
Mount the toggle switch to the front of the bottom plate and attach the cables.
Double check all your cables, PSU power, fan connectors toggle switch etc.
There is a small gap between the PSU holder and the fans where the fan cables can fit.
Place the front and back case on the bottom plate.
Lock everything in place by attaching the four corner screws to the big fan grille and the top right and bottom left screws to the small grille.

I don't really expect anyone to go through the hassle to build this, but if you do, I'd really appreciate a picture of your build!

There is definitely room for improvement to the design, feel free to use these files for a remix or to design your own case with this fans-as-a-structural-component idea. I'd love to see what you come up with.

Tagi