1 / 5
Audi A4 B8 RS4-Style Grille Badge / Emblem V3 — zdjęcie 1
1 / 5

Audi A4 B8 RS4-Style Grille Badge / Emblem V3

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

3D printable RS4-style grille badge designed for Audi A4 B8 / B8.5 honeycomb grilles. The model is optimized for FDM pri

Ocena
0 / 5
Polubienia
9
Pobrania
25
Wydruki
0
Wyświetlenia
193
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
GNU General Public License v3.0

RS4-Style Grille Badge for Audi A4 B8 / B8.5

This project is a 3D printable RS4-style front grille badge/emblem intended for custom and aftermarket honeycomb grilles used on the Audi B8 platform.

The model was designed with practical FDM printing in mind:

  • separate printable components,

  • simple geometry,

  • no unnecessary supports where possible,

  • fast test-fit workflow,

  • replaceable/reprintable individual parts,

  • suitable for PLA, PETG and similar FDM materials.

The package also contains diagnostic and test models that can be used to verify dimensions, fit and assembly before committing to the final print.

Intended applications

Suitable as a custom grille emblem for:

  • Audi A4 B8

  • Audi A4 B8.5

  • S-line / RS-style conversions

  • aftermarket RS4-style honeycomb grilles

  • custom front grille projects

⚠ Grille geometry varies between manufacturers.

Before final installation, verify the mounting area and dimensions on your particular grille.
RECOMMENDED PRINT SETTINGS

General

Technology: FDM / FFF
Nozzle: 0.4 mm
Layer height: 0.20 mm
Walls: 3–4
Top/Bottom layers: 4–5
Infill: 15–25%

For the mounting section, higher wall count is more important than very high infill.


MATERIAL

PETG — Recommended

PETG is recommended for a badge that will remain permanently installed on the vehicle.

Advantages:

  • better temperature resistance than standard PLA,

  • good impact resistance,

  • slightly flexible mounting features,

  • better suitability for exterior automotive use.

Suggested starting point:

PETG

  • 0.20 mm layer

  • 3–4 walls

  • 20–25% infill

PLA

PLA can be used for:

  • test fitting,

  • prototypes,

  • dimensional verification,

  • display models.

For permanent automotive exterior use, PETG or another temperature-resistant material is preferable.


PRINT ORIENTATION

Orient the visible face so that the cosmetic surface receives the best possible finish.

For multi-part versions, print the components separately when this gives better surface quality.

Check the slicer preview before printing, especially around:

  • thin logo features,

  • mounting tunnels,

  • internal gaps,

  • narrow walls.

A 0.4 mm nozzle is sufficient.


FIRST PRINT / FIT TEST

Before printing the entire badge:

  1. Print the supplied T01 test coupon.

  2. Check the mounting interface against your grille.

  3. Verify clearance.

  4. Verify the planned cable tie / mounting method.

  5. Only then print the final badge.

This saves material if your grille has slightly different dimensions.


ASSEMBLY

Depending on the grille version, the badge can be installed using the integrated mounting geometry and suitable small cable ties / fastening elements.

Recommended installation procedure:

  1. Dry-fit the badge.

  2. Check its position from the front.

  3. Verify that it sits parallel to the grille.

  4. Install the mounting fasteners.

  5. Tighten gradually.

  6. Do not overtighten PETG or PLA parts.

  7. Cut the excess cable tie material after final alignment.

The mounting system should hold the badge securely without requiring permanent modification of the grille.


MULTICOLOR PRINTING

For the best appearance, the badge can be printed using multiple filament colors.

Typical combination:

  • black base,

  • silver / grey details,

  • red RS accent.

This can be achieved using:

  • AMS / MMU,

  • manual filament changes,

  • separately printed components.

For manual color changes, inspect the slicer layer preview first and place the filament change exactly where required.


SURFACE FINISH

For a more OEM-like appearance:

  • use a smooth top surface,

  • enable monotonic top infill,

  • reduce visible seam placement on cosmetic surfaces,

  • use ironing only if your printer produces consistent results.

PETG with a matte or satin finish works particularly well for automotive trim parts.


OUTDOOR USE

Automotive exterior components are exposed to:

  • UV radiation,

  • heat,

  • freezing temperatures,

  • rain,

  • washing chemicals,

  • vibration.

Material selection therefore matters.

For permanent use:

PETG is the minimum recommended material.

For demanding environments, ASA or another UV- and temperature-resistant material may provide better long-term durability.


COMPATIBILITY NOTE

This model was designed around an RS4-style / honeycomb grille configuration for the Audi B8 platform.

Aftermarket grille manufacturers do not always use identical honeycomb dimensions.

Therefore:

Print the test coupon and verify your grille before printing the complete model.

If your grille dimensions differ, the mounting geometry may require adjustment.


PRINTABILITY

Designed for practical FDM manufacturing.

Target characteristics:

  • 0.4 mm nozzle compatible,

  • 0.20 mm layer compatible,

  • limited support requirement,

  • short test print available,

  • individual parts can be reprinted,

  • suitable for batch production.


FEEDBACK

If you print this model, please upload a Make and include information about:

  • vehicle model,

  • model year,

  • grille type/manufacturer,

  • filament,

  • printer,

  • any dimensional adjustments required.

This information can help improve compatibility in future revisions.


VERSION

V3

Development revision focused on:

  • geometry cleanup,

  • mounting validation,

  • logo printability,

  • assembly verification,

  • practical FDM production.


DISCLAIMER

This is an independent, fan-made/custom 3D printing project.

It is not an OEM Audi AG product and is not affiliated with, endorsed by, sponsored by or manufactured by Audi AG or Audi Sport GmbH.

Audi, RS4 and associated trademarks and logos are the property of their respective owners.

The model is provided for customisation, repair, prototyping and personal 3D-printing purposes.

Verify fitment and mounting security before operating the vehicle.


TAGS

audi
audi-a4
audi-a4-b8
a4-b8
a4-b8-5
b8
b8-5
rs4
rs4-badge
rs4-emblem
audi-rs4
grille
grille-badge
grille-emblem
honeycomb-grille
car-badge
car-emblem
automotive
car-parts
auto-parts
exterior
car-mod
audi-mod
audi-tuning
3d-printed-car-parts
petg
fdm

Tagi