PLAYMOBIL Steck Round Tower Roof Tip 3007691 (30076910) - 3666 Castle Top Cover
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
PLAYMOBIL Steck Round Tower Roof Tip – Part 3007691 / 30076910
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 27
- Wydruki
- 0
- Wyświetlenia
- 100
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Building Toys
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a 3D-printable replacement for PLAYMOBIL part 3007691 / 30076910, the round tower roof tip / top cover used on the classic PLAYMOBIL Steck castle construction system.
The original part can be found on the classic PLAYMOBIL 3666 castle and is also used with other compatible round-tower roof assemblies.
I tried to keep the model as close to the original part as possible, including the overall conical shape, top opening, four raised seam sections and the very small recessed details running along them.
Those small grooves are one of the most difficult parts of the model to reproduce properly with FDM printing. Because of this, I strongly recommend using the supplied 3MF instead of simply slicing the STL with a normal preset.
The 3MF includes specially tweaked super-high-quality PLA and PETG profiles for both 0.4 mm and 0.2 mm nozzles. These profiles are intended to preserve the small surface details that make the printed part look much closer to the original.
Using a normal preconfigured preset can simplify the geometry enough that the smallest grooves are barely visible or disappear completely when sliced. For example, the normal 0.08 mm High Quality preset for a 0.4 mm nozzle can still simplify these features considerably. Likewise, simply using the standard 0.06 mm preset for a 0.2 mm nozzle does not necessarily give the same result as the custom profiles included in the project.
For maximum detail, the included 0.2 mm nozzle PLA profile uses a 0.04 mm layer height. The included 0.4 mm nozzle profiles have also been specially configured to print at 0.06 mm, below the normal 0.08 mm minimum used by the standard A1 0.4 mm profile.
The model does not require supports when printed in the supplied orientation.
The dimensions, top socket and general shape were designed to match the original roof component as closely as possible. Because printer calibration and material shrinkage vary, minor cleanup or sanding of the connection area may occasionally be required.
INCLUDED FILES
3007691.stl – model for custom slicing
3007691_MULTI_QUALITY_PROFILES_PLUS_GENERIC_PLA_0.06_A1_0.4.3mf – recommended prepared project containing multiple high-detail PLA and PETG profiles
The supplied 3MF contains prepared options for:
PLA with a 0.2 mm nozzle
PETG with a 0.2 mm nozzle
PLA with a 0.4 mm nozzle
PETG with a 0.4 mm nozzle
Generic PLA with a 0.4 mm nozzle
PART NUMBER
3007691 / 30076910
TRADEMARK NOTICE
This is an independently recreated, unofficial compatible replacement part.
PLAYMOBIL is a trademark of its respective owner. This design is not affiliated with, endorsed by or sponsored by the trademark owner.
3D printing settings
3D PRINTING SETTINGS
Using the supplied 3MF is strongly recommended for this model.
The very small recessed grooves around the four roof seams can easily be simplified by the slicer when using ordinary quality presets.
The included 3MF therefore contains several custom high-detail profiles specifically configured to preserve as much of this geometry as possible.
AVAILABLE PRINT PROFILES
0.2 mm nozzle – PLA – Maximum detail
3007691 – Bambu PLA Matte 0.04mm Ultra HQ @ A1 0.2
Recommended when reproducing the fine surface detailing is the main priority.
Nozzle: 0.2 mm
Layer height: 0.04 mm
Initial layer height: 0.10 mm
Wall generator: Arachne
Walls/perimeters: 4
Infill: 12% Gyroid
Top layers: 10
Bottom layers: 8
Slicer resolution: 0.005 mm
Supports: Disabled
Outer-wall speed: 35 mm/s
Outer-wall acceleration: 1,200 mm/s²
This is the profile I would choose when the best possible reproduction of the small grooves is more important than print time.
0.2 mm nozzle – PETG
3007691 – CR PETG Clean Strong 0.06mm HQ @ A1 0.2
Nozzle: 0.2 mm
Layer height: 0.06 mm
Initial layer height: 0.10 mm
Walls/perimeters: 4
Infill: 12% Gyroid
Supports: Disabled
This gives a high-detail PETG option for users who prefer a slightly tougher and less brittle material.
0.4 mm nozzle – PLA Matte – Super HQ
3007691 – Bambu PLA Matte 0.06mm FORCED Super HQ @ A1 0.4
Nozzle: 0.4 mm
Layer height: 0.06 mm
Initial layer height: 0.20 mm
Wall generator: Arachne
Walls/perimeters: 4
Infill: 12% Gyroid
Top layers: 10
Bottom layers: 8
Slicer resolution: 0.005 mm
Supports: Disabled
Outer-wall speed: 40 mm/s
Outer-wall acceleration: 1,200 mm/s²
The project includes a custom Bambu Lab A1 0.4 mm nozzle – Forced 0.06mm Project machine preset.
This lowers the minimum permitted layer height from the normal 0.08 mm to 0.06 mm, allowing the included Super HQ profile to be used without changing the model geometry.
0.4 mm nozzle – Generic PLA – Super HQ
3007691 – Generic PLA 0.06mm FORCED Super HQ @ A1 0.4
A separate Generic PLA option is included for users who are not printing with Bambu PLA Matte.
Nozzle: 0.4 mm
Layer height: 0.06 mm
Initial layer height: 0.20 mm
Wall generator: Arachne
Walls/perimeters: 4
Infill: 12% Gyroid
Top layers: 10
Bottom layers: 8
Slicer resolution: 0.005 mm
Supports: Disabled
Outer-wall speed: 40 mm/s
Use the embedded Generic PLA filament profile as a starting point and adjust temperature if required for your particular filament.
0.4 mm nozzle – PETG – Super HQ
3007691 – CR PETG Clean Strong 0.06mm FORCED Super HQ @ A1 0.4
Nozzle: 0.4 mm
Layer height: 0.06 mm
Initial layer height: 0.20 mm
Wall generator: Arachne
Walls/perimeters: 4
Infill: 12% Gyroid
Top layers: 10
Bottom layers: 8
Slicer resolution: 0.005 mm
Supports: Disabled
Outer-wall speed: 35 mm/s
Outer-wall acceleration: 1,000 mm/s²
This profile is tuned more conservatively for PETG while still retaining the very small layer height required for the surface detailing.
IMPORTANT – DO NOT JUST USE A NORMAL QUALITY PRESET
If the decorative grooves are important to you, avoid importing the STL and simply selecting a standard profile.
The normal 0.08 mm High Quality profile for the 0.4 mm nozzle may simplify the smallest groove geometry enough that much of it becomes difficult to see in the finished print.
Likewise, a standard 0.06 mm 0.2 mm-nozzle preset should not be assumed to reproduce the same result as the specially configured profiles supplied with this model.
The custom 3MF changes more than just layer height. The high-detail profiles use settings such as fine slicer resolution, slower outer surfaces, additional shell layers and carefully selected wall generation to give the small geometry a better chance of surviving the slicing process.
For this particular model, preview the grooves in the sliced layer view before starting the print. If they disappear in the preview, they will not magically appear on the finished part.
MATERIAL
PLA / PLA Matte
PLA is recommended when the highest possible surface definition is the priority.
The supplied PLA profiles are particularly suited to reproducing the small recessed details.
PETG
PETG is also fully supported by the supplied 3MF and has dedicated profiles for both nozzle sizes.
PETG provides slightly more toughness and flexibility, although extremely fine surface details may not appear quite as crisp as they do with a well-tuned PLA print.
SUPPORTS
Supports are not required.
The model is designed to print in the orientation supplied in the 3MF without support material.
Do not automatically reorient the model unless you intend to develop your own print strategy.
TOP SOCKET STRENGTH
The prepared 3MF includes a local modifier around the upper socket.
This area is printed at:
100% infill
Zig-zag solid filling
The remainder of the model uses 12% Gyroid infill.
This strengthens the socket without unnecessarily printing the entire roof tip solid.
Keep this modifier enabled when using the supplied 3MF.
BUILD-PLATE ADHESION
The model has a relatively small contact area, so a brim is recommended.
The prepared object uses:
Brim type: Outer brim
Brim width: 5 mm
Brim/object gap: 0 mm
Clean the build plate before printing.
The zero-gap brim gives reliable adhesion but will require some cleanup after the print.
BRIM REMOVAL AND FINISHING
Allow the part to cool before removing it from the build plate.
Remove the outer brim carefully.
Trim any remaining brim material with flush cutters or a deburring tool.
Check the complete lower circumference for first-layer flare.
Remove any strings around the top socket.
Avoid sanding the decorative seam details unless absolutely necessary.
Test-fit the part gently on the original roof.
If the socket is slightly tight, lightly clean the contact surface rather than scaling the complete model.
CHOOSING A PROFILE
For the highest possible detail:
0.2 mm nozzle + 0.04 mm PLA Ultra HQ
For very high detail with a standard nozzle:
0.4 mm nozzle + 0.06 mm PLA Super HQ
For PETG with a standard nozzle:
0.4 mm nozzle + 0.06 mm PETG Super HQ
For PETG with a fine nozzle:
0.2 mm nozzle + 0.06 mm PETG HQ
Whichever profile you choose, inspect the sliced preview and make sure the small grooves are still represented before starting the print.