1 / 9
GYRONULL, a gyroscopic cancelling crown gear fidget spinner — zdjęcie 1
1 / 9

GYRONULL, a gyroscopic cancelling crown gear fidget spinner

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Every spinner fights back when you tilt it. This one cancels its own. No hardware, no supports, 13 parts.

Ocena
0 / 5
Polubienia
4
Pobrania
6
Wydruki
0
Wyświetlenia
102
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

GYRONULL

Pick up any spinner you own. Get it going, then turn your wrist. Feel that? The way it pushes back and wants to stay in its own plane? That is gyroscopic torque, and it is the reason a spinner feels alive in your hand. Every spinner ever made does it. Now do the same with this one. Nothing. It spins just as hard, it runs just as long, and your wrist feels absolutely nothing.


HOW THE CANCELLING WORKS

There are two rotors in here, not one, and they turn in opposite directions at exactly the same rate. Each rotor carries a 36 tooth crown gear. They face each other across the middle of the toy, and four pinions on a stationary cage sit between them. Drive one crown and the pinions drive the other one backwards. Same tooth count, same radius, so the rates are identical and opposite.

Angular momentum is polar moment times rate. The two rotors are the same STL printed twice, so their polar moments are identical, their rates are equal and opposite, and the two cancel. The sum is zero, and zero is what your wrist feels. It is the one thing about this model you cannot photograph. It has to go in a hand.


WHAT YOU ACTUALLY WATCH

The spinning half is the outside half. Each rotor carries a drum out to the full 88 mm width, so the widest thing on the toy is the part that moves, and the two drums leave a 10.6 mm window all the way round. Through it you watch the four pinions turning on the stationary cage while everything around them runs the other way. Both faces are cut with twelve swept windows.

The upper rotor is the same part turned over, so its sweep mirrors, and the two faces visibly swirl in opposite directions. The rotors were always going to run opposite ways. The sweep is what lets you see it, in a photograph as well as in your hand.


NOTHING HERE IS BOUGHT

No bearings. No screws. No magnets. No weights. No pins. No nuts. Nothing. All 13 pieces come off the plate, and the only fastening in the whole toy is a snap between the two stem halves, buried in the middle of the stator hub where it cannot fall out or work loose.


PRINTING IT

No supports. Not "minimal supports", none at all, anywhere, on any part. Four of the six parts print flat on a face and the axle pins lie down on a flat, so nothing has to stand up as a column and no overhang goes past 45 degrees.

01-rotor x2 web face down, teeth up

02-pinion x4 axis vertical

03-spider x1 flat, face down

04-stem-lower x1 touch face down, post standing

05-stem-upper x1 touch face down, socket opening up

06-axle-pin x4 lying down on its flat

Layer height 0.16 to 0.20 mm. 2-4 perimeters on the rotors.
15% infill is fine

One thing genuinely matters: PRINT THE TWO ROTORS IDENTICALLY. Same filament, same settings, same session. They are the same STL twice and that is not a convenience, it is the mechanism. Two rotors with different polar moments do not cancel, and the whole point of the toy leaks away.

13 pieces, 6 unique parts, 88 x 88 x 41.6 mm assembled, about 92 g in PLA.


PUTTING IT TOGETHER

1. Lower stem standing on the bench, pad down.

2. Lower rotor down over its post, teeth up. Its bore is a full circle, so it drops straight on with no orientation to find.

3. Spider down over the post, flats against flats. There are two flats, not one. Line them up and the cage cannot turn in your fingers.

4. Four pinions into their pockets, one axle pin through each.

5. Upper rotor down, teeth into the pinions.

6. Upper stem down onto the post until you feel the snap seat.


That click is the only assembly step that is not gravity. Then hold it by the two pads, flick a rotor rim hard, and turn your wrist. Compare it against whatever else is on your desk. That comparison is the entire product.

SPECS

Measured on the finished solids, not on the parameters that drew them: the two rotors' polar moments agree to 9.9e-14 percent net angular momentum about the spin axis, 2.6e-08 of 2.63e+07 dynamic imbalance 2.6e-09

REMIXES

Go ahead. If you scale it, scale both rotors by the same factor or you will throw away the only thing that makes it different. please share your make!


CREATED WITH

FORMA, free cad software. FORMA is free to download: https://downloads.3d3d.ca

Tagi