1 / 2
Desk Stand for Sonoff SNZB-06P — Uses the Original Magnetic Mount | Standfuß für Sonoff SNZB-06P — nutzt die Original-Magnethalterung — zdjęcie 1
1 / 2

Desk Stand for Sonoff SNZB-06P — Uses the Original Magnetic Mount | Standfuß für Sonoff SNZB-06P — nutzt die Original-Magnethalterung

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Holds the Sonoff SNZB-06P's original magnetic mount upright so the sensor can tilt down. No screws, no glue.

Ocena
0 / 5
Polubienia
1
Pobrania
10
Wydruki
0
Wyświetlenia
81
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Share Alike

### The Problem

The Sonoff SNZB-06P sits flat on its magnetic mount when placed on a shelf. In that position it can barely be tilted downwards, and it covers the room poorly.

### The Solution

This stand holds the original magnetic mount upright. The sensor then hangs above the base plate and can be tilted freely on its magnetic joint — up to roughly 22° before it touches down. Nothing is glued and nothing is screwed. The mount slides in from the front, clicks into place audibly, and is held by friction alone. A collar on the back stops it from sliding through. To remove it, push on the domed back from behind.

### Dimensions

- Footprint 40 × 52.3 mm, height 68.2 mm
- Around 19 g of material
- Print time approximately […]

### Printing

The back wall lies flat on the build plate, the base plate points straight up. This way the mounting bore is a vertical hole — round and dimensionally accurate. The file is already oriented correctly.

### Fit

The bore has 0.20 mm clearance against the measured mount (Ø 44.06 mm). On a Qidi Q2 in PETG
that is spot on: it goes in by hand and stays put. If it is too tight on your printer, sand the bore lightly. If it is too loose, a strip of tape around the rim of the mount does the job.


### Das Problem

Der Sonoff SNZB-06P liegt auf seiner Magnethalterung flach im Regal. In dieser Lage lässt er sich kaum nach unten neigen, und er erfasst den Raum schlecht.

### Die Lösung

Dieser Standfuß nimmt die mitgelieferte Magnethalterung auf und stellt sie senkrecht. Der Melder hängt dann über der Bodenplatte und kann auf seinem Magnetgelenk frei geneigt werden — bis etwa 22°, bevor er aufsetzt. Es wird nichts geklebt und nichts geschraubt. Die Halterung wird von vorn in die Bohrung geschoben, rastet spürbar ein und hält allein durch Klemmung. Ein umlaufender Kragen auf der Rückseite verhindert, dass sie durchrutscht. Zum Herausnehmen von hinten auf die gewölbte Rückseite drücken.

### Maße

- Grundfläche 40 × 52,3 mm, Höhe 68,2 mm
- Materialbedarf rund 19 g
- Druckzeit etwa […]

### Drucken

Die Rückwand liegt flach auf dem Druckbett, die Bodenplatte steht senkrecht nach oben. So ist die Aufnahmebohrung ein senkrechtes Loch — rund und maßhaltig. In der beigefügten Datei liegt das Teil bereits richtig.

### Passung

Die Aufnahmebohrung hat 0,20 mm Spiel gegenüber der gemessenen Halterung (Ø 44,06 mm). Auf einem Qidi Q2 in PETG sitzt das genau richtig: von Hand einzuschieben, hält von allein. Sollte es bei deinem Drucker zu stramm sein, hilft Schleifpapier in der Bohrung. Sitzt es zu locker, tut es ein Streifen Klebeband auf dem Rand der Halterung.

Tagi