1 / 7
Magnetic Tank Bag — Triumph Scrambler 1200 XC / XE — zdjęcie 1
1 / 7

Magnetic Tank Bag — Triumph Scrambler 1200 XC / XE

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a rigid, magnetic tank bag specifically designed to fit the contours of the Triumph Scrambler 1200 series tank.

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
0
Wyświetlenia
60
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a rigid, magnetic tank bag specifically designed to fit the contours of the Triumph Scrambler 1200 tank (fits all Scrambler 1200 X, XC, and XE models). I also do leatherwork so mine has leather topper, internal leather and soft kid leather covering magnet base, but it's not strictyl necessary (definitely use some kid leather to cover the magnets though).

The underside is custom-shaped to match the exact curve of the tank. Four Ø30 mm neodymium magnets hold the bag securely in place through the kid leather base to protect the paint. A hinged hard lid with a magnetic clasp opens away from you for easy access.

Printed in ASA for durability and heat resistance, all leather trim pieces can be cut using the included 1:1 A4 templates.

Fitment

Fits all Triumph Scrambler 1200 XC and XE models across all years (they all share the same tank profile). The conforming underside was measured directly from a 2019 XC model.

Printer Compatibility

Part

Dimensions (mm)

180 Bed (MINI+ / A1 mini)

250×210 (MK3S+ / MK4S)

256 (P1S / X1C / K1)

tank_bag_body

170 × 205 × 140

No

Yes

Yes

tank_bag_lid

175 × 220 × 70

No

Yes(rotate 90°)

Yes

tank_bag_hinge_leaf

78 × 36 × 17

Yes

Yes

Yes

tank_bag_leaf_shim_3mm

78 × 8 × 20

Yes

Yes

Yes

tank_bag_body_ring_alt + _floor_alt

181 × 206 / 170 × 205

No

Yes

Yes

STL Files Overview

  • Body tank_bag_body: Single-piece main tub (~400g). Recommended and tested option.

  • Lid & Hinge tank_bag_lid + tank_bag_hinge_leaf: The hinged top cover designed to use a Ø5 mm metal pin (no drilling required).

  • Leaf Shim tank_bag_leaf_shim_3mm: Required until you install the wall leather. The leather is load-bearing; without it or this temporary shim, the lid sits 3 mm off-center and will jam.

  • Two-Piece Body Alternative _ring_alt + _floor_alt: Designed for printers that struggle with tall ASA prints. Acetone-weld together along the floor joint using four 1.75 mm filament pins for alignment.

Recommended Print Settings (ASA)

  • Material: ASA is highly recommended over PETG due to high heat resistance in direct sunlight on dark fuel tanks.

  • Temperatures: 270 °C nozzle / 90–95 °C bed (enclosure strongly recommended).

  • Bed Surface & Adhesion: Textured PEI sheet + glue stick + 8 mm brim. Do not use a raft—the geometry causes ASA to warp off rafts. Pre-heat the bed for 20–30 mins before starting the body print.

  • Body Supports: Print tank-face up with grid supports (2.5 mm spacing, 0.1 mm top gap, 4 concentric interface layers) supporting the curved underside from the build plate only.

  • Lid Supports: Print dome-up with tree supports from the build plate only (make sure supports don't enter the hinge bores).

  • Walls/Infill: 3 perimeter walls, 20% gyroid infill, 0.20 mm layer height.

Hardware & Materials Needed

  • Magnets (Tank Base): 4 × Ø30 × 2 mm neodymium discs

  • Magnets (Lid Clasp): 2 × Ø30 × 3 mm neodymium discs

  • Hinge Pin: 1 × Ø5 mm steel rod (~90 mm length)

  • Fasteners: 3 × Chicago screws / binding posts (for hinge leaf, through leather)

  • Adhesives: Epoxy resin, contact cement (plus acetone if printing the 2-piece body)

Leather Preparation

The included 1:1 printable PDF templates contain 6 patterns:

  • Interior floor

  • Lid top crown & lid skirt

  • Inner and outer wall bands

  • Tank-facing magnet base (with pre-drawn magnet cutouts)

Print templates at 100% scale and verify using the 100 mm scale bar. Lightly wet-form or ease the leather during fitting where indicated on the patterns.

Assembly Steps

  1. Base: Epoxy the four base magnets into place (ensure matching magnetic polarity), then attach the leather base over them.

  2. Hinge: Secure the hinge assembly using Chicago screws (Stack order: Leaf | Shim/Leather | Wall) and insert the Ø5 mm pin.

  3. Clasp: Epoxy the clasp magnets into the lid and body.

  4. Leather Trim: Apply the outer leather wrap using contact cement. Remove the 3 mm plastic shim once the wall leather is installed.

Note: I am not responsible for your use of this model should your build somehow fail on the bike, print and use at own risk.


Tagi