1 / 4
Modular Ganesh Mandapam for 300 mm Idol – Gopuram & Chhatri — zdjęcie 1
1 / 4

Modular Ganesh Mandapam for 300 mm Idol – Gopuram & Chhatri

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A modular, structurally keyed home-pooja mandap for a nominal 300 mm Ganesh idol, with a support-free flat roof

Ocena
0 / 5
Polubienia
2
Pobrania
19
Wydruki
0
Wyświetlenia
159
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Creative Commons — Attribution

This is a large modular Ganesh mandapam designed around a nominal 300 mm-tall idol. It combines a practical keyed structure with a restrained Dravidian-inspired crown that is decorative without depending on fragile miniature sculpture.

The wide components are divided into printable quadrants. Square seam keys align the plinth and roof, each corner uses two keyed column sections, and the roof, gopuram and kalash all locate with dedicated printed pins. A fit-test coupon is included and should be printed before committing to the long parts.

Finished size

- Overall plinth: 420 × 340 × 30 mm

- Covered roof: 440 × 360 mm

- Overall height: approximately 687 mm

- Clear space between columns: approximately 302 mm wide × 222 mm deep

- Minimum clear height above the platform: approximately 400 mm

- Intended preview envelope for the idol: 260 × 200 × 300 mm

Measure the real idol at its widest and deepest points, including its own base, before printing.

Design highlights

- Four-piece stepped plinth with square alignment keys

- Eight universal keyed column sections

- Four simple flat roof quadrants that print without the earlier difficult inverted shell

- Fully covered chhatri-style canopy

- Hollow artistic gopuram with one continuous bottom-open chamber

- Gopuram base and roof centre both 210 × 210 mm for a clean transition

- Printable cornice blocks, broad shrine frames and four small corner finials

- Internal X-brace connecting the four gopuram mounting sockets

- Removable central kalash

Parts to print

- 4 base quadrants

- 8 copies of Column_Segment_PRINT_8.stl

- 4 roof quadrants

- 1 hollow gopuram crown

- 1 kalash finial

- 1 connector-peg set

- 1 fit-test coupon before everything else

The connector set contains the required seam keys and mounting pins plus spares.

Suggested print settings

- PETG preferred; PLA/PLA+ is acceptable only away from heat and direct sun

- 0.4 or 0.6 mm nozzle

- 0.24–0.28 mm layer height

- Base and roof: 4–5 walls, 5 top/bottom layers, 18–25% gyroid or cubic infill

- Columns and pegs: 5–6 walls, 30–40% gyroid or cubic infill

- Gopuram: 4 walls, 10–15% infill; do not generate support inside the hollow chamber

- Column sections: print socket-end down with a 10–15 mm brim

- Roof quadrants: print exactly as supplied on the full flat underside; normally no support

- Kalash: print upright with a 10–15 mm brim

Assembly

1. Print and test the clearance coupon.

2. Join the four base quadrants with the 8 mm square seam keys.

3. Seat one column section in each base socket and add the second section above it.

4. Join the four roof quadrants on a flat table with the remaining seam keys.

5. Insert the four 14 mm roof pins into the columns and lower the assembled roof over them.

6. Use four 10 mm pins to locate the gopuram on the roof.

7. Insert the kalash into the top socket.

8. Confirm the completed mandap sits flat without rocking before placing the idol.

Glue is optional for a temporary setup but recommended at the roof and plinth seams for a permanent installation. Two-part epoxy or thick cyanoacrylate can be used after a successful dry fit.

Colour concept

The included Blender scene uses warm temple ivory, antique-gold cornices and finials, kumkum-maroon roof/shrine accents, and a dark teak plinth. The validated production STLs remain single-colour geometry; use the renders as a painting or multicolour-planning guide.

Safety and physical-fit limits

Digital mesh checks do not establish a load rating, impact resistance, long-term creep strength or printer-specific fit. The roof is intended to carry only the printed gopuram and lightweight decorations. Do not hang lamps, bells, wet garlands or other heavy loads from it. Lift the mandap from the plinth, never from the roof or crown.

Never place a lit diya, camphor flame, incense ember or hot metal tray on or directly beneath printed plastic. Use a separate stable metal or stone fire tray well in front of the mandap with generous clearance and adult supervision. PETG is more heat tolerant than PLA but is not fireproof.

Tagi