SW32 Armaturenschlüssel / Open Basin Wrench – Sunlight Cliff Adventure 602 RT
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Offener SW32 Armaturenschlüssel / basin wrench für den Sunlight Cliff Adventure 602 RT Campervan.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 4
- Wydruki
- 0
- Wyświetlenia
- 48
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution
# Deutsch
Dieser offene SW32-Armaturenschlüssel wurde für den Sunlight Cliff Adventure 602 RT Campervan konstruiert und dort praktisch getestet.
Die Armaturenmutter sitzt auf einem langen Gewinde. Direkt darunter verlaufen die roten und blauen Warm- und Kaltwasseranschlüsse, die seitlich vom Gewinde abknicken. Ein normaler Maulschlüssel erreicht die Mutter nicht. Ein geschlossener Rohrschlüssel oder eine tiefe Stecknuss kollidiert mit den Wasseranschlüssen.
Der Schlüssel kann seitlich über Gewinde und Anschlüsse gesetzt werden. Die offene Konstruktion lässt ausreichend Platz für die abgewinkelten Leitungen.
## Konstruktion
- Schlüsselweite: SW32
- Innenmaß: 32,6 mm über Flächen
- 30 mm tiefe Aufnahme
- Schlüsselkopf 120° offen
- etwa 240° Kontaktfläche an der Mutter
- darunter 180° offener Halbkanal
- 40 mm freier Innenraum
- zwei getrennte, konisch zulaufende Handgriffe
- kein Querbalken zwischen den Griffen
- Gesamtlänge: 110 mm
- Gesamtbreite der Griffe: 96 mm
Zum Nachsetzen wird der Schlüssel leicht von der Mutter abgehoben, um 60° gedreht und wieder aufgesetzt.
Das Modell wurde speziell für den Sunlight Cliff Adventure 602 RT entwickelt. Es kann auch bei anderen Campervans, Wohnmobilen oder Armaturen funktionieren, sofern eine SW32-Mutter und ausreichend ähnliche Platzverhältnisse vorhanden sind.
Empfohlene Datei:
SW32_spuelenschluessel_V3_druckorientiert_kopf_unten.stl
Diese STL ist bereits für den Druck ausgerichtet:
- SW32-Kopf liegt auf dem Druckbett
- Halbkanal wird senkrecht aufgebaut
- Handgriffe wachsen langsam nach außen
- normalerweise keine Stützstruktur notwendig
Empfohlene Einstellungen:
- Material: PETG, PETG-CF, PA/Nylon oder PC
- Schichthöhe: 0,24–0,28 mm
- Wände: 6–8
- obere und untere Schichten: mindestens 6
- Infill: 50–70 % Gyroid oder Cubic
- Support: aus
- Brim: 5–8 mm empfohlen
PLA kann für geringe Belastungen funktionieren. Für ein Werkzeug sind PETG, Nylon oder PC die bessere Wahl.
## Passprobe
Vor dem vollständigen Schlüssel sollte die Datei
SW32_passprobe_V3_8mm.stl
gedruckt werden.
Das Innenmaß beträgt 32,6 mm und enthält bereits etwas Spiel für den FDM-Druck. Drucker, Material und Slicer können das tatsächliche Maß beeinflussen.
Wenn die Passprobe zu eng ist, kann der Parameter across_flats in der OpenSCAD- oder Python-Datei angepasst werden.
## Enthaltene Dateien
- druckorientierte STL
- STL in normaler Werkzeuglage
- 8-mm-Passprobe
- parametrische OpenSCAD-Datei
- Python-Generator
- Vorschau
- Validierungsinformationen
Die STL-Dateien wurden auf Wasserdichtigkeit, zusammenhängende Geometrie und beschädigte Flächen geprüft.
Der Schlüssel ist für normale Armaturenmuttern und moderates Handdrehmoment gedacht. Bei festsitzenden oder korrodierten Metallmuttern sollte ein Metallwerkzeug verwendet werden. Gedruckte Werkzeuge können bei Überlastung plötzlich brechen.
---
# English
This open SW32 basin wrench was designed for and tested in a Sunlight Cliff Adventure 602 RT campervan.
The faucet mounting nut sits on a long threaded shaft. The red and blue hot and cold water connections bend away directly below it. A normal open-end wrench cannot reach the nut, while a closed tube wrench or deep socket collides with the angled water hoses.
The open design allows the wrench to be placed sideways over the threaded shaft and hoses without bending or trapping the connections.
## Design
- Wrench size: SW32
- Internal size: 32.6 mm across flats
- 30 mm deep gripping section
- Wrench head open by 120°
- Approximately 240° contact around the nut
- 180° open half-channel below the head
- 40 mm internal clearance
- Two separate tapered finger grips
- No crossbar between the grips
- Overall length: 110 mm
- Overall grip width: 96 mm
To reposition the wrench, lift it slightly off the nut, rotate it by 60°, and place it back onto the nut.
The model was designed specifically for the Sunlight Cliff Adventure 602 RT. It may also fit other campervans, motorhomes, RVs or faucet installations that use an SW32 mounting nut and have similar clearances.
## Printing
Recommended file:
SW32_spuelenschluessel_V3_druckorientiert_kopf_unten.stl
This STL is already oriented for printing:
- SW32 head placed on the build plate
- Half-channel printed vertically
- Finger grips grow outward gradually
- Normally no support structures are required
Recommended settings:
- Material: PETG, PETG-CF, PA/Nylon or PC
- Layer height: 0.24–0.28 mm
- Perimeters: 6–8
- Top and bottom layers: at least 6
- Infill: 50–70% gyroid or cubic
- Supports: disabled
- Brim: 5–8 mm recommended
PLA may work for light use. PETG, Nylon or PC is a better choice for a functional tool.
## Fit test
Print this file before printing the complete wrench:
SW32_passprobe_V3_8mm.stl
The socket measures 32.6 mm across flats and already includes some clearance for FDM printing. Actual fit depends on the printer, material and slicer settings.
If the fit gauge is too tight, adjust the across_flats parameter in the included OpenSCAD or Python source.
## Included files
- Print-oriented STL
- STL in normal tool orientation
- 8 mm fit gauge
- Parametric OpenSCAD source
- Python generator
- Preview image
- Mesh validation information
The STL files were checked for watertightness, connected geometry and broken faces.
This printed tool is intended for normal faucet mounting nuts and moderate hand torque. Use a metal tool for seized or heavily corroded fittings. Printed tools can break suddenly when overloaded.
