1 / 5
Resonara Vase — Wrapped Acoustic Nodal Field — zdjęcie 1
1 / 5

Resonara Vase — Wrapped Acoustic Nodal Field

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A one-piece support-free vase shaped by wrapped acoustic standing waves and flowing nodal paths.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
11
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Standard Digital File License

Resonara Vase - Wrapped Acoustic Nodal Field

Resonara turns sound into form. Its surface is generated from three coupled mathematical standing-wave modes wrapped around a calm vessel, creating broad pressure cells divided by deep, flowing nodal paths.

This is not a repeated rib, spiral, woven texture, or decorative displacement map. The acoustic modes interfere across the full height and circumference, so every cell has a different proportion and every viewing angle reveals a new network of highlights.

Features

• Original wrapped acoustic nodal-field design
• Three coupled standing-wave families: 4×5, 6×3 and a 9×2 detuning mode
• Deep recessed nodal paths with a controlled master silhouette
• One-piece construction with no assembly
• Approx. 132.15 × 122.11 × 205 mm
• Modeled 2.37 mm estimated minimum radial wall
• Modeled 4.0 mm bottom
• High-resolution closed manifold STL with 554,496 triangles
• Blender source, procedural generator and GLB preview included

The geometry includes a directional FDM limiter. As the vase rises, each exterior contour is allowed to expand only as far as the layer below can support. This preserves the acoustic relief while keeping the printable surface inside a conservative 45-degree envelope.

Use normal printing mode with 0% infill and 4 perimeters. Do not enable Spiral/Vase mode because the wall and bottom are already modeled into the geometry.

Matte PLA gives Resonara the appearance of carved ceramic or cast stone. Silk PLA emphasizes the pressure cells and moving nodal highlights. PET-G is also suitable when improved moisture resistance is useful, but dry filament and controlled cooling are recommended for the deepest paths.

Although the STL is geometrically watertight, an FDM print is not automatically watertight. Test the finished print before adding water, or use a removable liner or suitable interior sealant.

The model has been digitally validated as one closed manifold component with no boundary edges, non-manifold edges, disconnected parts, degenerate triangles, or critical downward surfaces beyond 45 degrees. A first physical test print is still recommended.

Licensed under the Standard Digital File License. Personal use only unless separate commercial permission is granted by the creator. For commercial licensing, contact the creator through the Printables profile.

────────────────────────

Print Instructions - Resonara Vase

Recommended setup

• Orientation: upright, exactly as supplied
• Nozzle: 0.4 mm
• Layer height: 0.20 mm; use 0.16 mm for finer nodal paths
• Line width: 0.42–0.46 mm
• Walls/perimeters: 4 recommended; 3 minimum
• Top solid layers: 10 recommended
• Bottom solid layers: 10 recommended
• Infill: 0%
• Supports: none intended
• Brim: optional 6–8 mm if bed adhesion is unreliable
• Outer-wall speed: 30–40 mm/s
• First-layer speed: 15–25 mm/s
• Seam: align on the least visible rear side; avoid random seam placement
• Wall generator: Arachne/variable-width is recommended when available

The STL already contains its complete wall and 4.0 mm bottom. Use normal printing mode. Do not enable Spiral/Vase mode.

Why the acoustic cells print without support

The procedural generator applies a directional layer-to-layer limiter after the acoustic field is created. Exterior growth is restricted to 0.72 mm for every 1.0 mm of vertical rise, leaving margin below the theoretical 45-degree threshold. The final STL was independently checked by the Majesti mesh validator and PrusaSlicer.

PLA starting profile

• Nozzle: 205–220 °C; start at 215 °C
• Bed: 55–65 °C; start at 60 °C
• Part cooling: 80–100% after the first layers
• Overhang speed: 25–35 mm/s

Devil Design PET-G starting profile

• Nozzle: 230–240 °C; start at 235 °C and follow the spool range
• Bed: 70–80 °C; start at 75 °C
• Part cooling: 35–55% after the first layers
• Outer-wall speed: 30–38 mm/s
• Retraction: use the calibrated PET-G value for your printer
• Dry the filament if stringing, popping, or surface bubbles appear

Avoid excessive first-layer squish with PET-G. Use a suitable release layer on print surfaces where PET-G may bond too aggressively.

Scaling

The intended size is 100%. At 80% scale, the estimated minimum radial wall is reduced to approximately 1.90 mm and remains reasonable for many calibrated 0.4 mm setups. Inspect every nodal path in the slicer before aggressive downscaling.

Water use

A geometrically watertight STL does not guarantee a watertight FDM print. Test the finished vase over a sink and leave it on an absorbent surface for several hours. Additional perimeters, calibrated flow, PET-G, a liner, or a suitable interior sealant can improve water resistance.

This model has been digitally validated but has not yet been physically print-tested.

Tagi