Modular Japanese Noren Clamp & Hanging Mount (36 cm)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Modular clamp to hang 36cm Japanese noren. Glueless interlocking design with keyholes & cord mounts.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 29
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Creative Commons — Attribution
A clean, modular clamping system designed to hang traditional Japanese Noren tapestries flat against the wall without sewing rod pockets or damaging the fabric.
The complete assembly consists of two clamped bars:
Top Hanging Mount: Clamps the top edge and features dual mounting options (blind wall keyholes or top cord pass-throughs).
Bottom Ballast Bar: Clamps the bottom edge to add downward tension and keep the fabric straight and wrinkle-free.
Each 380 mm bar is split into two interlocking 200 mm halves connected via a screw-locked lap joint, allowing the entire model to print flat on standard 3D printer beds (≤ 200 mm footprint).
Key Features
No Glue Required: The center lap joint is secured directly by the central clamping screw and nut.
Dual Hanging Options:
Two-Screw Wall Mount: Blind rear keyhole slots (spaced 200 mm apart).
Single-Nail Hanging: Integrated vertical cord pass-through holes with bottom knot recesses for paracord, leather cord, or hanging wire.
Fabric Grip Ridges: Continuous internal ribs grip the fabric firmly across the entire width without puncturing or tearing it.
100% Support-Free: All overhangs, joint steps, and nut pockets are oriented to print flat on the build plate with zero supports.
Bill of Materials (BOM)
Printed Parts
Top Clamp Assembly (Plate 1):
1xFront Left1xFront Right1xRear Left (with Keyhole & Cord Mounts)1xRear Right (with Keyhole & Cord Mounts)
Bottom Ballast Assembly (Plate 2):
1xFront Left1xFront Right1xRear Left (Solid)1xRear Right (Solid)
Fasteners & Hardware
10 × M3 × 14 mm countersunk (or 16 mm if not countersunk) Machine Screws (5 per bar)
10 × M3 Hex Nuts (standard DIN 934 / ISO 4032)
Hanging Hardware (Choose one):
Wall Screws: 2 × Wall screws/nails with head diameter ≤ 8.0 mm.
Hanging Cord: ~60–80 cm of 2–3 mm cord (paracord, hemp, leather, or picture hanging wire).
Recommended Print Settings
Material: PLA (I used Prusament Woodfill PLA), PETG, or ABS/ ASA
Orientation: Print all parts flat on the build plate (Z-height = 8 mm)
Layer Height: 0.20 mm
Supports: Use some support if necessary. The 3MF has some supports added.
Infill: 3 perimeters, 15–20% infill (keeps it lightweight)
Assembly Instructions
Insert the Hex Nuts: Push the 5 M3 hex nuts into the hexagonal pockets on the rear clamp halves (press-fit).
Assemble the Rear Bar: Slide the Rear-Left and Rear-Right segments together at the center overlap step.
Assemble the Front Bar: Slide the Front-Left and Front-Right segments together at the center overlap step.
Position the Noren: Lay the top edge of your 36 cm Noren onto the rear bar, aligning the fabric within the side margins. I recommend placing everything on a flat surface to make sure everything is aligned.
Clamp and Fasten: Place the front bar over the fabric. Insert the 5 countersunk M3 screws and tighten them into the rear hex nuts. Tighten the center screw first to lock the modular joint together, then tighten the outer screws.
Repeat for Bottom: Assemble the bottom clamp and fasten it to the lower edge of the noren for tension.
Hang:
Keyhole Method: Hook the two rear keyhole slots directly onto two level wall screws.
Cord Method: Feed your cord down through the top eyelets on each end, tie an overhand knot beneath each corner so it sits recessed inside the bottom pocket, and hang the loop from a single nail.
Disclaimer: OpenSCAD generated with help from Gemini 3.7 Flash. OpenSCAD included in case you want to remix this for different sizes, etc.
