1 / 1
Anycubic Kobra Neo (v1) Nozzel Silikon Cleaning Pad Mount — zdjęcie 1

Anycubic Kobra Neo (v1) Nozzel Silikon Cleaning Pad Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

a cleaning pad for a silicone nozzel cleaner

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
24
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Since my new Kobra 4 is now my new workhorse, I finally had some time to get my old Kobra Neo working again.

Here is a mount for a nozzle cleaning pad. It is designed for a silicone pad that fits the Kobra 4.

You need Klipper to use the nozzle cleaning function at all. I mostly adapted the Kobra 4 cleaning process for the Kobra Neo.

Printing:
Regular PLA is totally fine. Simply put the part onto the front-left bed arm. It’s a tight fit and sits right at the front. Just force it over the arm until it is fully seated. You can remove it anytime.

Add the silicone pad, and you’re ready to go.

My Macro:

Before using the macro, check the position manually first!!!!!
I am not responsible for any damage. You can and should adjust the values to suit your setup and needs.

Cheers!

Macro:

[gcode_macro NOZZLE_CLEAN]

description: Nozzle Cleaning (3 passes) with heating, cooling and parking

gcode:

# ============================================================

# Settings

# ============================================================

{% set heat_temp = 140 %}

{% set cool_temp = 120 %}

{% set wipe_speed = 100 %}

{% set travel_speed = 300 %}

{% set clean_z = 1.0 %}

{% set cool_z = -0.5 %}

{% set safe_z = 10 %}

{% set wipe_count = 3 %}

# ============================================================

# 0. Check Homing & Bed temperature log

# ============================================================

{% if "xyz" not in printer.toolhead.homed_axes %}

G28

{% endif %}

# Aktuelle Betttemperatur aus den Druckerdaten auslesen

{% set current_bed_temp = printer.heater_bed.target %}

M117 Nozzle Clean: Bed temp maintained

RESPOND MSG="NOZZLE CLEAN: Bed temperature maintained at {current_bed_temp}C"

# ============================================================

# 1. Heat nozzle to cleaning temperature

# ============================================================

M117 Nozzle Clean: Heating

RESPOND MSG="NOZZLE CLEAN: Heating nozzle to {heat_temp}C"

M109 S{heat_temp}

M117 Nozzle Clean: {heat_temp}C reached

RESPOND MSG="NOZZLE CLEAN: {heat_temp}C reached - cleaning starts"

# Absolute Positionierung

G90

# ============================================================

# 2. Move to cleaning position

# ============================================================

M117 Nozzle Clean: Moving to start

RESPOND MSG="NOZZLE CLEAN: Moving to cleaning position"

G1 Z{safe_z} F600

G1 X-11.5 Y-15.5 F{travel_speed * 60}

G1 Z{clean_z} F600

# ============================================================

# 3. Nozzle Cleaning (angepasst an neues Pad)

# ============================================================

M117 Nozzle Clean: Cleaning

RESPOND MSG="NOZZLE CLEAN: Cleaning - {wipe_count} passes"

{% for wipe in range(wipe_count) %}

M117 Nozzle Clean: Pass {wipe + 1}/{wipe_count}

RESPOND MSG="NOZZLE CLEAN: Wipe pass {wipe + 1}/{wipe_count}"

# Vorwärts (von X -11.5 nach X 50 mit Zickzack über Y)

G1 X50 Y-10.5 F{wipe_speed * 60}

G1 X-11.5 Y-13.0 F{wipe_speed * 60}

G1 X50 Y-15.5 F{wipe_speed * 60}

# Rückwärts

G1 X-11.5 Y-13.0 F{wipe_speed * 60}

G1 X50 Y-10.5 F{wipe_speed * 60}

G1 X-11.5 Y-15.5 F{wipe_speed * 60}

{% endfor %}

M117 Nozzle Clean: Cleaning done

RESPOND MSG="NOZZLE CLEAN: Cleaning completed"

# ============================================================

# 4. Lower nozzle to Z-0.5 and cool down

# ============================================================

M117 Nozzle Clean: Lowering

RESPOND MSG="NOZZLE CLEAN: Lowering nozzle to Z{cool_z}"

# Düse leicht ins Pad einpressen (Z -0.5), um Tropfen zu verhindern

G1 X50 Y-11.5

G1 Z{cool_z} F600

# Lüfter zur Unterstützung auf 100%

M117 Nozzle Clean: Cooling

RESPOND MSG="NOZZLE CLEAN: Cooling fan 100% - cooling to {cool_temp}C"

M106 S255

# Warten bis Cool-Down Temp erreicht ist

M109 S{cool_temp}

M117 Nozzle Clean: {cool_temp}C reached

RESPOND MSG="NOZZLE CLEAN: {cool_temp}C reached"

# Lüfter ausschalten

M107

M117 Nozzle Clean: Cooling done

RESPOND MSG="NOZZLE CLEAN: Cooling completed - fan off"

# ============================================================

# 5. Move to safe position for mesh probing

# ============================================================

M117 Nozzle Clean: Parking

RESPOND MSG="NOZZLE CLEAN: Moving to safe Z and bed center"

G1 Z{safe_z} F600

G1 X110 Y110 F{travel_speed * 60}

M117 Nozzle Clean: Complete

RESPOND MSG="NOZZLE CLEAN: Complete - ready for mesh"

Tagi