PressDock M6 – Mac mini Airflow Stand with Easy Power Button

PressDock M6 is a low-profile, one-piece desktop stand designed to keep the Mac mini in its normal horizontal position while leaving the underside airflow path open.

The four rounded corner cups follow the enclosure contour, so the Mac sits inside the stand instead of appearing to float above it. The middle of every side remains open for ventilation and easy cable access.

KEY FEATURES

• One-piece printable base
• Open 118 × 118 mm central airflow area
• Four rounded contour-following corner cups
• Five raised support zones positioned outside the approximate vent-ring envelope
• Press-from-top access to the hidden underside power button
• Three included power-button calibration shims: 0.2, 0.4 and 0.6 mm
• Recesses for five protective felt/EVA pads
• Optional recesses for four 10 mm rubber feet
• No print supports required

COMPATIBILITY AND FIT

Designed for the compact Mac mini enclosure used by:

• Mac mini M6 (2026)
• Mac mini M5 Pro (2026)
• Mac mini M4 (2024)
• Mac mini M4 Pro (2024)

• Mac mini: 127 × 127 × 50 mm
• Stand envelope: approximately 142 × 142 × 21.2 mm
• Raw device cavity: 128.2 × 128.2 mm
• Total XY clearance: 1.2 mm
• Estimated enclosure corner radius: 8.8 mm
• Corner-cup inner radius: 9.4 mm
• Radial corner clearance: 0.6 mm

Not compatible with Mac mini M2/M2 Pro (2023), M1 (2020), or earlier Intel models.

Apple publishes the external enclosure dimensions but not a detailed bottom drawing or corner-radius specification. The power-button position and enclosure corner radius are therefore engineering estimates based on reference photography. Print one test piece before relying on the fit for long-term use.

POWER BUTTON

The rear-left support is intentionally replaced by a sub-flush circular pusher. Place the Mac mini with its front ports facing the front of the stand. Start with the 0.4 mm shim and lightly press the top rear-left corner of the Mac to actuate the underside power button.

If the button does not activate, try the 0.6 mm shim. If it is too sensitive or constantly touches the button, use the 0.2 mm shim or remove the shim.

For normal shutdown, use the macOS Shut Down command. Holding the physical power button should only be used for a forced shutdown when necessary.

RECOMMENDED PRINT SETTINGS

• Material: PETG or ASA
• Nozzle: 0.4 mm
• Layer height: 0.20 mm
• Perimeters/walls: 4
• Top layers: 5
• Bottom layers: 6
• Infill: 18–25% gyroid or adaptive cubic
• Orientation: flat bottom on the build plate
• Supports: not required
• Optional brim: 4–6 mm if bed adhesion is weak

PETG is recommended for the first print because it offers better long-term heat resistance than standard PLA.

ASSEMBLY

1. Add approximately 0.9 mm felt or EVA to the five upper pad recesses.
2. Optionally install four 10 mm adhesive rubber feet underneath.
3. Attach the 0.4 mm power shim to the circular pusher using thin double-sided tape.
4. Place the Mac mini inside the four corner cups.
5. Confirm that the power button is not constantly pressed.
6. Test with a gentle press on the top rear-left corner and adjust the shim if needed.

FILES

• One-piece stand base
• 0.2 mm power shim
• 0.4 mm power shim
• 0.6 mm power shim

VALIDATION

The mesh was digitally checked as one connected manifold component with zero boundary and non-manifold edges. It was also successfully sliced in PrusaSlicer. The design has not yet been physically test-printed, so user feedback and measured fit results are welcome.

This is an original, AI-assisted design. Apple and Mac mini are trademarks of Apple Inc. This project is not affiliated with or endorsed by Apple.

LICENSE

Files are provided under the Printables Standard Digital File License. For separate commercial licensing, contact the creator through the Printables profile.